Firmware versions 1.1.xx
The following cofigurations are for 12 crank (24cam) tooth primary trigger, single cam tooth secondary trigger.
As found in Toyota, Honda, Mazda, and Nissan with CAS converter disk ( VehicleFitment/Nissan )
4 Cylinder
In config.txt
primary_trigger=07 # coil type, filtering, rising edge.
secondary_trigger=19 # camsync, rising edge.
tooth_wheel=18 # decimal 24 tooth (between cam pulses)
trigger_tooth=01 # or upto 05
ign_tdcdelay=B4 # 90/0.5 = 180 (half degrees)
another_trigger_tooth=06 # 24 tooth/4 cylinders
tooth_wheel_twidth2=00 # No missing tooth
tooth_wheel_twidth1=78 # decimal 120 (30deg / 0.25)
rpmk[0]=0b
rpmk[1]=b8 #RPM constant for 4 cyl = 3000 (=0x0bb8)
alternate=13 # injgroups 3..0 (fire all banks during cranking)
ignchmax=03 # ignition 3..0
cam_sync_r_edge_phase=33
cam_sync_f_edge_phase=46
reset_engphase_after=40 # since 720/0.25 = 2880%256 = 64
In tables.txt
h[1]=00 12 0C 06 00 12 0C 06 # another_trigger_tooth=06
h[2]=10 30 20 00 10 30 20 00 # Firing order: 1, 3, 4, 2
6 Cylinder
In config.txt
primary_trigger=07 # coil type, filtering, rising edge. Alternatively 06 would be falling edge (could be suitable for HALL, but not for VR)
secondary_trigger=19 # camsync, rising edge; alternatively 1d is same, but with filtering
tooth_wheel=18 # decimal 24 tooth (between cam pulses)
trigger_tooth=01 # or upto 03
ign_tdcdelay=C4 # 98 crankdegrees
another_trigger_tooth=04 # 24 tooth / 6 cylinders
tooth_width is allowed to be higher than 64 degrees. The missing tooth width is the upper byte. (there is no missing tooth anyway). Use 0 if the tooth distance is less than 64 degrees.
tooth_wheel_twidth2=00
tooth_wheel_twidth1=78 # decimal 120, that is 30 crankdeg per tooth
rpmk[0]=07
rpmk[1]=d0 # RPM constant for 6 cyl = 2000 (=0x07d0)
alternate=15 # injgroups 5 .. 0 (fire all banks during cranking)
ignchmax=05 # ignition 5..0
reset_engphase_after=40 # since camsync is used
In tables.txt
h[1]=00 14 10 0C 08 04 .. ..
h[2]=10 60 50 40 30 20 .. ..
8 Cylinder
In config.txt
primary_trigger=07 # coil type, filtering, rising edge.
secondary_trigger=19 # camsync, rising edge.
tooth_wheel=18 # decimal 24 tooth (between cam pulses)
trigger_tooth=01 # or upto 05
another_trigger_tooth=03 # 24 tooth/8 cylinders
tooth_wheel_twidth2=00 # No missing tooth
tooth_wheel_twidth1=78 # decimal 120 (30deg / 0.25)
cam_sync_r_edge_phase=33
cam_sync_f_edge_phase=46
rpmk[0]=03
rpmk[1]=e8 #RPM constant for 4 cyl = 3000 (=0x03E8)
ign_tdcdelay=B4 # 90/0.5 = 180 (half degrees)
alternate=17 # injgroups 7...0 (fire all banks during cranking)
ignchmax=07 # ignition 7...0
reset_engphase_after=40
In tables.txt
h[1]=15 12 0F 0C 09 06 03 00
h[2]= <depends on firing order>