Members Page/Sascha/Audi Coupe - VEMS wiki www.vems.hu

MembersPage/Sascha/AudiCoupe (2006-08-30 21:15:34)

This page contains information on helping a a friend with a Audi Coupe with a 5cyl 20V Turbo enigne conversion (like a european Audi S2)... running VEMS, w/ stock Auditrigger setup and stock COP w/o power output stage and 440cc high impeadance Ford Racing injectors.

So far, the ECU was ordered setup for Auditrigger, and I assume that one of the grounds was bad and this is why we cooked the P259 chip (confirmed with Jorgen), so it was removed and the two diodes put in place.

Before I reconnected the ECU, I reconnected all of the grounds myself (as I didn't install the VEMS in the first place, I just took over when they couldn't figure out the trigger setup).

The hall sensor is recieving 5V (from PIN 28 - verified this @ the hall plug - also during cranking), the hall sensor wiring is NOT sheilded! But the original Audi harness is also not using sheilded cable (only for the two VR sensors).

I'm also using a 5V pullup with a 22k ohm resistor for the crankhome VR sensor, without this pullup I wasn't able to get any rpm signal to the ECU.

The VR sensors are within spec as far as the ohm readings go... One has 974ohm, and the other 1007 ohm.

MT does show RPM values when cranking (between 100-180 rpm).

I have captured a mmd0c log which can be viewed here:

NOTE TO DOWNLOAD THE FILES, CLICK ON THE LINK, SCROLL TO THE BOTTOM OF PAGE AND CLICK DOWNLOAD!

http://www.freefileupload.net/file.php?file=files/300806/1156968999/mdd0c.log

Running through auditrigger_logformatter: the mdd0c seems very wrong, sectrig all over the place. Like if there was extreme noise on sectrig. Check grounds. It would be very useful if you could record crankhome-VR with your soundcard. See ElectronicDesign/SoundRecorder, I find it very unlikely you can progress without seeing what's going on.\n

56 45 4d 53 20 76 31 2e 30 20 31 32 x  31 32 20 k70 a3d 32 2c 32 48 ell6f 3e 0d _  x  x  0d _  x  x  x  0d _  0d _  x  x  0d _  0d _  x
  P  0d _  x
x  x  0d _  x  P  a6 0d _  a6 x  x  x  x  0d _  0d _  x  P  0d _  x  P  0d _  0d _  x  P  0d _  x  0d _  P  P  a6 x  x  0d _  x  P  0d
_  x  P  a6 a6 x  x  0d _
x  P  a6 a6 0d _  x  0d _  x  P  0d _  a6 0d _  x  0d _  0d _  x  0d _  x  0d _  x  x  0d _  x  P  0d _  a6 x  x  x  x  0d _  0d _  x
0d _  P  x  0d _  x  P  a6
a6 0d _  x  x  0d _  x  P  0d _  a6 x  x  x  x  x  x  0d _  x  P  x  x  0d _  x  P  x  x  0d _  x  0d _  P  0d _  x  P  a6 0d _  x  P
a6 0d _  a6 x  x  x  0d _
x  0d _  x  P  a6 a6 x  x  x  x  0d _  x  P  0d _  a6 x  x  x

here the mcd.log:

http://www.freefileupload.net/file.php?file=files/300806/1156969552/mcd.log

and here the mct.log:

http://www.freefileupload.net/file.php?file=files/300806/1156969628/mct.log

and also a copy of my MSQ:

http://www.freefileupload.net/file.php?file=files/300806/1156969697/20VT+auditrigger+-+base.msq

Injector's are connected to the following outputs:

Inj 1 - EC36 Pin7

Inj 2 - EC36 Pin19

Inj 3 - EC36 Pin8

Inj 4 - EC36 Pin20

Inj 5 - EC36 Pin9