I would like to install a Genboard v3.3 to the following car:
Audi S2 coupe quattro 2.2 5 cyl 20v 3B
My V3.3 include:
- Primery trigger VR
- secondary_trigger: auditrigger
- MAP connection: 400kPa onboard
- LCD an PS2
- 2 Knock and EGT
- ignition driver: 6+2
The car absolutely factory but the air filter's house was removed.
I want to make a street racing car from above.
My planning:
-I use a factory 55 pins Motronic male connector to EC18 and EC36 and make a flying cable set + WBO2,egt custom made wirings to engine.
-Anti lag system
-Launch control
-Boost control solenoid
-Distributor based ignition
-Sequential injection for 5 cyl '14.5 ohm'
-2 knock sensors, but I think use 1 knock sensor and the other knock's input I use the factory airmass sensor
-Primery trigger 135 cranktooth VR
-Secondary tr. hall trig1 camtooth
-Secondary tr. VR trig1 cranktooth
-Factory CLT,IAT,TPS
-1xWBO2,EGT
-LCD
Please check my planning pinout and if this not right you send for me please the correct.
EC36-1 TPS sign.
2-IAT 450-650 ohm/20cels
3-Idle actuator??? or boost control solenoid
4-
5-GND5
6-
7-Injector1 14.5 ohm
8-Injector3
9-Injector5
10-
11-
12-
13-Sec.trig HALL camtooth
14-CLT 2.1-2.9kohm/20Cels.
15-Fuel pump
16-
17-
18-
19-Injector2
20-Injector4
21-GND5
22-Injectr flyback+12v
23-Inj.fly.+12v
24-
25-Vbatt 15+
26-GND ecu and sign,knock
27-Primary trigger 135 cranktooth VR
28-5V to sensors /to TPS maybe ????
29-
30-
31-
32-GND5
33-
34-
35-
36-Coil /Distr.based ign/ or to the 35????
EC18-1
2-Knock1
3-Knock2 or air mass sensor???
4-
5-
6-
7-WBO2 pump-
8-
9-WBO2 pump+
10-
11-
12-Sec trigger Cranktooth VR?????????????????????
13-WBO2 nernst cell
14-Comm rs232 DSUB pin3
15-DSUB pin2
16-??????????? what is it?
17-
18-WBO2 heater-
Here is mine(NanassyPeter)
EC36-1 TPS signal,usually center pin
2-IAT ,other pin must be grounded
3-
4-
5-GND5!!!!!!!
6-
7-Injector1
8-Injector3
9-Injector5
10-
11-
12-
13-
14-CLT ,the other pin of CLT sensor must be grounded
15-Fuel pump
16-
17-
18-
19-Injector2
20-Injector4
21-GND5!!!!!!!!!!!!
22-
23-Inj.fly.+12v!!!!!!!!!
24-
25-Vbatt 15+ via relay and fuse
26-GND ecu and sign,knock (CLT,TPS,MAT)
27-Primary trigger 5 window HALL
28-5V to sensors, YES to TPS
29-BUT HERE IS THE TPS 5V SUPPLY,so use this instead of ec36p28
30-
31-
32-GND5!!!!!!!!!
33-
34-
35-Coil Drive
36-
EC18-1
2-
3-
4-
5-
6-
7-WB5
8-
9-WB6
10-
11-
12-
13-WB1
14-Comm rs232 DSUB pin3
15-DSUB pin vagy forditva ,ezt most nem tudom megerositeni
16-
17-
18-WB4
WB2 is not connected
WB3 is ignition + (15+)