I would like to install a Genboard v3.3 to the following car:
Audi S2 coupe quattro 2.2 5 cyl 20v 3B
This 5cyl needs InputTrigger/AudiTrigger see config info
- see GenBoard/UnderDevelopment/FirmwareChanges
- MegaTune r027 or later will be needed (r028 should work too).
- When I can use the new modified software version of original auditrigger?
While the trigger is special, the other sensors should be no problem at all.
My V3.3 include:
- Primary trigger VR
- secondary_trigger: auditrigger
- MAP connection: 400kPa onboard
- LCD an PS2
- 2 Knock and EGT
- ignition driver: 6+2
The car use the absolutely factory sensors and accessory but the air filter's house was removed.
I want to make a street racing car from above.
Project to follow:
- samco turbo hoses
- tubular turbo exhaust manifold
- bigger turbo than original
- erl water injection
- engine internal modification /pistons,conrods/
My plans:
- use a factory 55 pins Motronic male connector to EC18 and EC36 and make a flying cable set + WBO2,egt custom made wirings to engine.
- Anti lag system
- Launch control
- Boost control solenoid
- Distributor based ignition
- Sequential injection for 5 cyl '14.5 ohm'
- 2 knock sensors, but I think use 1 knock sensor.
- Primary trigger VR 135 tooth crankwheel (no missing tooth)
- Secondary tr. HALL trig 1 window/720° camtooth. Overlaps VR.
- Secondary tr. VR trig 1/360° cranktooth
- factory CLT
- factory IAT
- factory TPS
- 1xWBO2
- 1xEGT
- LCD
Please check my planned pinout and correct it if necessary.
EC36
1 TPS sign.
2-IAT 450-650 ohm/in 20°C
3- fast-idle small solenoid or relay (or any low-current output, such as shiftlight). EC36pin3 is a 350mA output, see GenBoard/Manual/DigitalOut/Table. You might want to use the powerful injector outputs first (don't forget to adjust h[0]=.. entries) and use the low-current outputs if you run out of injector outputs. Care is needed to not overload outputs.
4-
5-GND5
6-
7-Injector1 14.5 ohm/in 20°C
8-Injector3
9-Injector5
10-
11-
12-
13-Sec.trig HALL 1 window camtooth
14-CLT 2.1-2.9kohm/in 20°C
15-Fuel pump relay
16-
17-
18-BOOST solenoid
19-Injector2
20-Injector4
21-GND5
22-GND5
23-Inj.flyback injector common (+12V)
24-
25-Vbatt 15+
26-GND ecu and sign,knock
27-Primary trigger 135 cranktooth VR
28-5V to sensors /to TPS maybe ????
29-
30-
31-
32-GND5
33-
34-
35-ignition coil
36-
http://shop.x-dsl.hu/catalog/product_info.php?cPath=1&products_id=48 says channel3=EC36pin36 and channel5=EC36pin12 are logic-level drive. Useful for active coils that have the driver stage inside. For traditional dumb coil, you want to use one of the 6 power (non-logiclevel) ignition outputs. h[2]=.. (ignition sequence) must be adjusted for the chosen output in any case.
EC18
12-Knock1
3-
4-
5-
6-
7-WBO2 pump-
8-
9-WBO2 pump+
10-
11-
12-Sec trigger 1 Cranktooth VR
13-WBO2 nernst cell
14-Comm RS232 See [assembled genboard item in shop]
15-Comm RS232
16- 1-wire is a network connection. Not used (unless for [i-button]). A free connection (if you don't solder the DS2480B chip) - use for whatever you like.
17-
18-WBO2 heater-
DO NOT forget to read the warning of the provided resckue-kit paper, about GND5, flyback, and fuses.
Please link to the docs you're trying to use. See MegaTune page for (simple unzip) install.
The v3.3 has max232, so a standard RS232 port is needed. See GenBoard/Manual/CommHardware
If unsure about MegaTune setup / compatibility, in 9600,8n1 say \n
Man mll mcd mct bye
without spaces. mll prints LCD content of active page (even if no LCD connected), mcd and mct prints config and tables. bye (note: everything is case sensitive) goes back to MegaTune compatible mode. Since MegaTune is much simpler to use, you don't need to learn GenBoard/MenuSystem, but if you like:
But 1.0.19 will NOT work with the InputTrigger/AudiTrigger , since it is a new development.
megaloq viewer:
http://www.vems.hu/wiki/index.php?page=LogAnalysis
you can also collect some infos from:
http://www.msefi.com/index.php