VEMS Home Products Documentation Wiki Webstore
WikiHome ProjectPage DocsPage UnderDevelopment MembersPage SiteIndex RecentChanges Preferences
MembersPage/PhatBob/UserGuide (2015-01-01 07:00:00)

VEMS v3.3 installation instructions

These instructions are written for a typical Windows Installation. It is important to follow the guide in the defined steps, failure to do this may result in you frying your VEMS module.

In-car installation

Although VEMS has good environmental protection the engine bay of a car is still a very hostile place to install your VEMS module, so its a good idea to follow the lead of most car manufacturers and keep the ECU inside the passenger compartment.

Setting up your PC

The easiest way to configure and tune your VEMS unit is to use a PC, there are a number of tools which will need to be installed before we can start to setup VEMS.

MegaTune package, the latest version of which can be obtained from: http://www.vems.hu/wiki/index.php?page=MegaTune

<<MegaTune, WinTools in here.>>

Step One - Connecting power & testing

The EC36 is the larger Econoseal 36pin plug, and EC18 is the smaller Econoseal plug.

The first thing to do is to get a power supply upto the

NOTE: Signal Ground pin has many connections (CAS, TPS, IAT, CLT ...) make provision for this in your wiring loom.

The 3 Power Grounds (also called as "GND5" in some documents)

These (at least the first 3) must be connected to BATTERY- (preferrably with 3..4 separate wires that meet as close to the BATTERY- as possible). Failure to do this may result in damage to the VEMS module.

ConnectingPower.png

Make sure the EC36-pin5 connection does not break during operation. This is the reason for using separate wires: even if 1..2 breaks for some reason (eg. a screw comes loose), at least 2 remains connected.

Before you put any power through the unit use a multimeter to ensure that pins are wired correctly. There is little point in connecting power until the serial connector or LCD screen has been connected.

Connecting serial port

To allow the connection of the VEMS unit to your PC a serial port plug must be connected as follows.

ConnectingSerialPort.png

Connecting the LCD

The LCD option is a very useful addition to your VEMS module - with the use of an IBM PC keyboard it becomes invaluable as you will be able to configure your system without having to use a laptop. In the first instance it will provide a method of checking that your VEMS system is working. At present the LCD is provided without wiring, so you will need to connect it using a Female DB9 plug in the following way:

To control brightness and contrast (connection advice)

To connect the LCD to VEMS (suggested wire colour)

ConnectingLCD.png

Testing the VEMS unit

First connect your VEMS serial cable (see Step Two), and make sure that there are no applications that use the serial port running on your PC, applications such as Palm Pilot HotSync.

Connect the EC-18 connector with the serial port to VEMS.

And then connect the EC-36 connector with the power supply.

Navigate to the directory that you installed MegaTune into and double click on the megatune.exe application, and you will be presented with a window:

SelectProject.png

Select the VEMS Standard 12x12 (Default) option and click OK.

MTMainScreenWrong.png

On the Menu bar select Communications->Settings...

CommunicationSettings.png

Select the com port that VEMS is connected to, and click the 'Click to test' button, if all is well you will see the success message

CommunicationSettingsTested.png

This shows that your VEMS module is alive and communicating with the PC, close the Settings window and you should see something similar to this:

MTMainScreen.png

Close MegaTune and disconnect VEMS from its power supply.

Step Two - Connecting and configuring sensors

The trigger is the engine management system's most fundamental sensor, without one VEMS cannot calculate engine speed or crank angle. If you are connecting VEMS to an engine that has an existing engine management system, if not then a triggering method will need to be put in place.

The simplest type of trigger is to use the existing distributor to provide a pulse for each cylinder. This type of trigger is more than adiquate for

Connecting the primary trigger (CAS)

Magenetic sensor / Variable reluctance (VR)

Mechanical considerations (need to be written somewhere and referenced from here)

The VR sensing circuitry is very sensative to electrical noise, sheilded cable (coax) must be used and good grounding is vital.

ConnectingPrimaryTrigger.png

Sheilding should be grounded to engine block close to the VR Sensor.

Hall Sensor

VEMS is available configured for Hall sensors, these are more noise tollerant and require a +5V supply.

ConnectingPrimaryHallTrigger.png

Connecting the secondary sensor (optional)

Magenetic sensor / Variable reluctance (VR)

With the same considerations with the primary trigger regarding electrical noise.

ConnectingSecondaryTrigger.png

Hall Sensor

ConnectingSecondaryHallTrigger.png

Configuring the system to suit the sensor

[insert config file fragment]

Testing the crank sensor

Use MegaTune. Spin the engine. Watch the rpm value.

What to do if it doesn't work.

Connecting the inlet air temp. sensor (IAT)

ConnectingIAT.png

Connecting the coolant temp. sensor (CLT)

ConnectingCLT.png

Configuring the temperature sensors

Use EasyTherm to build tables.

Upload tables.

Testing the temperature sensors

Using MegaTune.

Check ambient temperature with thermometer

Check sensors reading on MegaTune or Motuner, compare with thermometer.

Apply known heat (boiling water) and check reading.

Apply known cold (ice) and check reading.

Connecting the throttle position sensor (TPS)

ConnectingTPS.png

Configuring and testing the TPS

MegaTune TPS setup. Steps and screen shots.

Connecting WBO2 Sensor (optional)

ConnectingWBO2Sensor.png

Before we plug the wide band in we need to do some tests and calibration, the first is 'Pump Zero DC', you will need to take a reading with a DVM across pins 5&6 of the Wideband connector. The ideal voltage is zero, to adjust the voltage you will need to change the values of wbo2_pump_pw_zero in config.txt. wbo2_pump_pw_zero value is adjusted during factory test, saved in ECM eeprom. Don't forget to save the output of Manmcd before tinkering with MegaTune or settings. wbo2_pump_pw_zero also written in the WebShop "Sentout" notification email. However, it is recommended to do the test to be sure.

Ideally the value should be between 0x63 to 0x66 (0x64 and 0x65 is most common) and the values make a big difference, for example at 0x65 I measured 0.10v changing to 0x64 resulted in a reading of -0.17 and 0x66 took the reading up to 0.4v. Note that WBO2 must be restarted for the value to take effect (reboot the board, or use mde02mde00 command).

Testing WB02 sensor

Fresh air reading

Configure value to read fresh air O2 level

Connecting exhaust gas temperature sensor (EGT) - Optional

Temp. compensated cable, blah blah blah.

EGTConnector.jpg

Configuring EGT sensor

Before we can rely on the sensor's readings we need to calibrate VEMS. This is best done using boiling water as we know that at sea-level this boils at 100degreesC. Make sure that the sensor does not touch the sides of the vessel containing the boiling water as this will result in an inaccurate reading. At 100degreesC the voltage fromt the sensor (measured across pins 1&8) should read:4.095mV and AD597's output (pins 4&6) will be 1005mV.

Calibration is required to enable VEMS to display and log the temperature value correctly, there are two values in the Config file that are used to do this:

(The change values are quite small so try increasing in steps of +/-0x5 initially.)

The EGT reading should be on the LCD screen's first page, to show EGT alone you can use Bray terminal to change to page 8 by using the command: Manmde08. Put the first few centimeters of the thermocouple onto some ice and watch the value on the scree drop. Adjust the calibration values until the egt reading is zero.

Testing EGT sensor

Then using a known temperature heat source (like boiling water) to check that the egt value is correct across a wide range.

Connecting manifold air pressure (MAP) sensor

In most cases the MAP sensor is built in to the VEMS module, but it's also possible to use an external sensor if required.

To connect the internal MAP you will need to route some 8mm tubing from the manifold to the VEMS module

Step 3 - Connecting Output Components

NOTE: VEMS acts as a switch between the Component (injector, relay, ignition coil) and ground. VEMS does not provide the power to these components.

VEMS output ports are listed here:

http://www.vems.hu/wiki/index.php?page=GenBoard%2FManual%2FDigitalOut%2FTable <<Remove this link>>

Connecting fuel injectors

VEMS can control anything from 1 to 8 fule injectors individually, although it's also possible to control upto 16 injectors grouped in twos.

IT IS ESSENTIAL that EC36-pin23 is connected to the Injector's common power supply (see diagram), EC36-pin23 controls the voltage spikes that the injectors produce when they close (flyback), failure to connect the flyback pin will fry your VEMS.

This shows the typical installation for a 4 cylinder application.

ConnectingInjectors.png

To 8 injectors are wired as shown here.

ConnectingInjectors8.png

And to pair injectors in parallel.

ConnectingInjectorPairs.png

The injector common + signal is connected with a 10A fuse to a switched +12V supply. NOTE the flyback connection is after the fuse.

Configuring VEMS for your Injectors

Configuring Injector Flow

Open MegaTune and select the Basic Settings item from the Settings menu. We will need to calculate the value Req Fuel(ms) to suit the injectors we're using.

mt04.jpg

Basic req_fuel calculation:\nÿ1ÿ

This is a simplified equation, if you are interested in the reasoning behind it you can read more here: http://www.vems.hu/wiki/index.php?page=GenBoard%2FManual%2FConfig%2FInjectorOpening

Examples\n

850cc injectors on a 2litre engine
6.49 * (1998/4/850) = 3.81mS

So the required fuel value will be entered as 3.8\n

280cc Injectors on a 1.6litre engine
6.49 * (1597/4/280) = 9.25mS

So the required fuel value will be entered as 9.3

Configuring Injector Impedance

High Impedance (HighZ)

In here, we write some stuff

Low Impedance (LowZ)

Here we do some PWM calcs.

Connecting the fuel pump

The fuel pump is controlled via a mechanical relay.

ConnectingFuelPump.png

Connecting ignition components

Single coil

In some instances you will want to keep the distributor, in this case VEMS can be configured to use the original coil as shown.

ConnectingSingleCoil.png

Coil pack

Connecting a two coil (4 cylinder wasted spark)

ConnectingCoilpack.png

Additional coil packs, for applications such as 8 cylinder wasted spark, can be connected:

ConnectingTwoCoilPacks.png

Coil on plug (COP)

There are two types of coil on plug (COP) passive and active.

Passive COPs are essentially just the standard type of coil of the type shown above, but with one coil per plug. These are driven by a high current +12v supply as supplied by VEMS ignition drivers.

More modern cars have an active COP, where the plug's ignition is controlled by a +5v signal. VEMS will need to be ordered specifically for this type of COP.

ConnectingCoilOnPlug.png

Configuring Ignition

In the 'settings' -> 'Priming, Cranking, Afterstart' window in megatune you find a field called 'Crank Advance(deg)' set that to 0 for now. That will make it easier to set the base timing.

Now make an easy to see mark at #1 TDC on the pulley and strope the engine when cranking. In the 'Settings' -> 'Trigger settings' window in megatune you find a field called 'TDC after the trigger(deg)' Change the value in that field until the timing light show that you have 0 deg timing when cranking.

If you need to set more then around 75 - 80 degrees in that window you should increment the 'Trigger tooth' field in the same window and try again. Each increment will lower the 'TDC after the trigger(deg)' with six degrees.

After you are satisfied with the settings you set the 'Crank Advance(deg)' to 10-15 degrees. That should be suitable settings for your engine.

Mine had bad hot starting when I had 6 degree crank advance.

Idle Air Controller (IAC)

An Idle Air Controller (IAC) is used on most fuel injected engines to provide a method of controling the engine's idle speed. When the car is warming up or an additional load is put on the idling engine such as the additional current of an electical fan or air conditioning compressor it is necessary to raise the engine's idle speed to stop it from stalling.

IAC Types

There are a number of different idle speed controllers:

Wax is the simplest and most common on Japanese cars and are not controllable by the ECU in that they use a wax filled piston which opens the throttle slightly when cold and closes it when the heat causes the wax to expand.

Solanoid IACs use a single coil to open or close a valve in the inlet (in some cases to actually move the throttle plate). The simplest can be either opened or closed and will cause small increase in idle speed. More sophisticated types can be pulsed to provide a variable increase in RPM.

Multicoil and Stepper motor IACs alow a much more complex level of control, in its simplest form it will have two coils to open and close the idle valve.

Choosing the correct IAC connection

Single coil types are relatively simple to connect, the only thing you need to know is the resistance of the IAC's coil by measuring it with a DVM. Once you have the resistance value use Ohms law to calculate it's current load. I=V/R.

Examples:

The IAC coil for a Nissan 200SX is measured at ~11 ohms a voltage of 13.8V would mean a current of ~1.26A (13.8/11) which means that a spare high current port (EC36-pins6, 9, 17 or 18) would need to be used.

[insert HighCurrentIAC.png picture here]

The Toyota "Idle Up Valve" found on the early 4A engines has a solanoid coil with a resistance of ~44ohms, which gives a current of 313mA(13.8/44). As this is less than the maximum 350mA value for EC36-pin3 (Fast Idle) it would be possible to connect it, but this is only advisable if you are using all the other high current pins. In all other cases its advisable to use one of the spare pins.

[insert LowCurrentIAC.png picture here]