Back to MembersPage/NanassyPeter
Pending
- MAT ignition retard.
- custom oil temp/pressure gauge with V3.3 and LCD
should check the relevant page, IIRC these are not yet implemented
GenBoard/UnderDevelopment/StagedInjectors
- 5 primary injectors, driven sequentially
- and another 5 staged. (note: 2 free injector drivers on this 5cyl engine, because fuelpump switched from an injector channel as well). Document the flowrate of injectors - the ratio of primary and secondary is very important because it must be configured
We have 10 Audi S3/TT high impedance (14ohm) 420ccm "shorty" injectors.So basically we run the same in the staged group as in the sequential "main" injector group.
- Possibly 5 connected (while the FET and EC36xx pin would be happy to drive 5 injectors, highz or properly configured lowz, but this could abuse the flyback.
- or 2+3 split. This is recommended. It's OK to switch them simultaneously though, like h[0]=xx xx xx xx xx xx xx 60 where 60 (decimal 96) is sum of 20 and 40 (decimal 32 and 64) to switch injF and injG (see GenBoard/Manual/DigitalOut/Table)
Sorry ,this section is totally chinees for me....
Please explain it a bit more.
Is it possible to configure fuel pump out to another "thing",to have all 8 injector FETs? How this works on a V8 engine ,where all 8 injectors have to be driven independently?
- I have 8 separately driven injectors with the fuel pump fed separately. See MembersPage/DavidBlades/FanTest for my config.
Anyway,is there any difference between:
1 inj FET driving 2 injectors
VS.
1 inj FET driving 3 injectors??
What injector behaviour can i expect if i drive 2 injectors from 1 inj FET,this way i do not need staging,all injectors will work all the time.There is NO NEED for lean idle,this is a race project.Im basically looking for options here....
A: We have driven 3,4 and 5 high-z injectors on the same outputs on a few cars. With the powerflyback board you will most likely have no problem with driving those high-z injectors in pairs. They aren't too big. //Emil
How can i insert the new ALS functions (MembersPage/GaborRacz/NewAlsLaunchAndOthers) in the 1.0.30firmware and Megatune??
Q
I still experience some unwanted EGO behaviour sometimes,the EGO correction just switches off (no correction at all),even tough it would be needed!
Please tell me which MegaTune variable to set and which direction??And what is this all about?
Firmware 1.0.35 problem
i installed the 1.0.35,and the config and tables that Marcell made for me.Upgrade went very rough,firmware 35 didnt wanted to talk vith AVR,but it was successfull for the 3rd-4th time.
The tables very damaged a little,only 1-2 rows were off,nothing dramatical.
The main problem is that i cant control the fuel pump.In my previous 30 firmware ,it just worked FINE,i controll it with P259/6. I tried different settings under MT,but i can only swith it off.
Here my mcdmct
_ello>
primep=00
primep_temp_scaling=00
cwl=2F
cwh=0A
cranking_thres=02
awev=41
awev_temp_scaling=0F
awec=C0
warmup_clt_range[0]=00
warmup_clt_range[1]=0F
warmup_clt_range[2]=23
warmup_clt_range[3]=37
warmup_clt_range[4]=50
warmup_clt_range[5]=64
warmup_clt_range[6]=78
warmup_clt_range[7]=8C
warmup_clt_range[8]=AA
warmup_clt_range[9]=C8
warmup_clt[0]=B4
warmup_clt[1]=AC
warmup_clt[2]=A0
warmup_clt[3]=90
warmup_clt[4]=83
warmup_clt[5]=7E
warmup_clt[6]=78
warmup_clt[7]=70
warmup_clt[8]=6B
warmup_clt[9]=64
warmup_rpm_scale=BF
req_fuel=32
divider=01
alternate=14
injopen=00
battfac=13
kpafac=78
kpaoffs=87
injocfuel=2A
injrampup_battfac=FF
injpwm=FF
injpwmt=0A
injpwm6=70
rpmk[0]=09
rpmk[1]=60
tpsdot_kpadot_conf=00
tpsdotrate[0]=08
tpsdotrate[1]=0F
tpsdotrate[2]=19
tpsdotrate[3]=28
tpsaq[0]=01
tpsaq[1]=02
tpsaq[2]=05
tpsaq[3]=0A
als_cut_mintps=FF
tpsasync=02
acmult=C8
tpsacold=96
launch_enrich=00
launch_retard=00
overrun_fuelcut=14
overrun_fuelresume=13
rev_limit=4D
airden_ignore=00
config11=41
config12=40
config13=02
batt_cal=A3
fastidle=C6
als_max_cut=00
dbaro=0C
tps_low=2A
tps_high=F5
fan_temp=FC
fan_hyst=05
fan_channel=FF
iac_step_seq=C9
iac_conf=48
iac_max_steps=FF
iac_tps_thres=08
iac_cold_idle_temp=90
iac_warm_idle_temp=C6
iac_cold_rpm=78
iac_warm_rpm=5C
iac_cold_start_pos=00
iac_warm_start_pos=00
iac_afterstart_rpm=01
iac_afterstart_duration=32
iac_speed=05
iac_kp=00
iac_ki=00
iac_kd=00
launch_rpm=14
iac_integral_limit_dec=80
iac_integral_limit_inc=80
iac_integral_deadband=0A
iac_deadband=05
als_cut_maxtps=00
iac_overclose_interval=32
iac_ref_pos[0]=FF
iac_ref_pos[1]=FF
iac_ref_pos[2]=FF
iac_ref_pos[3]=FF
iac_ref_pos[4]=FF
iac_ref_pos[5]=F2
iac_ref_pos[6]=80
iac_ref_pos[7]=73
iac_ref_pos[8]=6B
iac_ref_pos[9]=00
iac_sol_channel=60
iac_ign_slope=20
softrpm_range=3F
iac_ign_advance_limit=08
iac_ign_retard_limit=08
iac_ign_threshold=08
ego_conf=06
ego_lag=01
ego_coolant=B4
ego_maxtps=E6
ego_maxmap=FF
ego_minrpm=06
ego_maxrpm=49
ego_warmup=3C
ego_lean_limit=33
ego_rich_limit=0D
ego_pid_kp=28
als_enrich=00
ego_delta=59
ego_target=19
ego_pid_window=FF
wbo2_warmup_ramp=C0
als_react_tps=00
wbo2_abs_limit=F5
wbo2_limit_maxt=A0
wbo2_fallback=60
wbo2_retry_t=06
wbo2_edgetime_corr=BA
wbo2_edgetime_min=50
wbo2_ri_target=9A
wbo2_nernstdc_target=9D
wbo2_pump_pw_zero=64
wbo2_calibration=CE
wbo2_heater_pid_kp=46
wbo2_heater_pid_ki=10
wbo2_heater_pid_kd=1A
wbo2_heater_pid_ilimit=80
wbo2_pump_pid_kp=15
wbo2_pump_pid_ki=37
wbo2_pump_pid_kd=00
wbo2_pump_pid_ilimit=FF
wbo2_ri_confidence_scale=80
knock_conf=01
knock_sampling_window=FF
knock1_frequency=29
knock1_gain=3F
knock1_integrator=1F
knock2_frequency=29
knock2_gain=3F
knock2_integrator=1F
knock_threshold=FF
knock_noise_scale=FF
knock_max_retard=00
knock_default_retard=00
knock_retard_step=00
knock_retard_delay=00
knock_advance_step=00
knock_advance_delay=00
knock_minrpm=FF
knock_maxrpm=FF
ve_learn_coolant=D8
ve_learn_max_power=FF
ve_learn_rpm_scale=1E
ve_learn_kpa_scale=1E
ve_learn_ego_scale=43
ve_learn_min_weight=4D
ve_learn_speed=FF
ve_learn_limit=33
ve_learn_conf=00
lcd_c0=FE
lcd_delay=FF
lcd_backlight=FF
kpa_conf=21
ign_balance=00
als_retard_mintps=FF
als_retard_maxtps=00
lcd_default_view=00
primary_trigger=CE
secondary_trigger=02
tooth_wheel=05
trigger_tooth=00
another_trigger_tooth=1E
crank_minper=60
tooth_wheel_twidth1=00
tooth_wheel_twidth2=00
cam_sync_r_edge_phase=01
cam_sync_f_edge_phase=02
reset_engphase_after=F0
ign_tdcdelay=62
ign_dwell14=30
ign_dwell6=38
ign_crank_advance=24
ign_out=70
ignchmax=04
engine_off_delay=00
pump_on_mintime=00
fuelpump_channel=6F
inj_stage2_rate=FF
inj_stage2_start_tps=FF
inj_stage2_start_map=FF
als_deact_rpm=FF
als_deact_time=01
als_deact_egt=00
als_retard=00
als_rev_limit=40
misc1out_minrpm=01
misc1out_maxrpm=FF
misc1out_mintps=FF
misc1out_maxtps=FF
misc1out_minmap=FF
misc1out_maxmap=FF
misc1out_channel=FF
misc2out_minrpm=FF
misc2out_maxrpm=FF
misc2out_mintps=FF
misc2out_maxtps=FF
misc2out_minmap=FF
misc2out_maxmap=FF
misc2out_channel=FF
act_wot_rpm=FF
act_wot_channel=FF
act_rpm_rpm=FF
act_rpm_channel=FF
egt1_cal=47
als_tks_channel=FF
boost_conf=00
boost_targetoffs=00
boost_minpressure=FF
boost_pid_kp=20
boost_pid_ki=80
boost_pid_kd=01
boost_pid_ilimit=FF
boost_channel=FF
water_pump_temp=FC
hybrid_rpm_a=00
hybrid_rpm_m=00
water_pump_hyst=00
water_pump_channel=FF
toothrel_normal=66
toothrel_missing=7F
fuelcut_min_kpa=12
fuelcut_max_kpa=FF
tach_channel=FF
tach_divider=FF
shiftcut_conf=01
shiftcut_channel=00
shiftcut_time=00
softrpm_rpm=28
j[0]=2B80 2C80 2C80 3080 3180 3180 3280 3180 3180 2E80 2D80 2A80
j[1]=2F80 3080 3A80 3D80 3E80 3E80 3E80 3D80 3C80 3A80 3980 3580
j[2]=3D80 3F80 4380 4580 4780 4780 4880 4780 4780 4480 4280 3F80
j[3]=5680 5780 5180 5480 5580 5480 5380 5180 5180 4F80 4E80 4980
j[4]=6180 5F80 5B80 5C80 5C80 5C80 5B80 5A80 5A80 5680 5680 5580
j[5]=6680 6580 6380 6580 6680 6580 6580 6580 6380 6080 5F80 5D80
j[6]=6C80 6D80 6F80 6F80 7080 6F80 6F80 6D80 6C80 6980 6780 6680
j[7]=7980 7980 7980 7980 7980 7980 7880 7780 7680 7480 7280 7080
j[8]=7D80 7D80 7D80 7D80 7D80 7D80 7C80 7C80 7B80 7980 7A80 7A80
j[9]=8080 8080 8080 8080 8080 8080 8080 8080 7F80 7D80 7C80 7B80
j[A]=8480 8480 8380 8180 8280 8280 8380 8380 8180 8080 7F80 7C80
j[B]=8180 8180 8180 8280 8180 8280 8280 8180 8280 7F80 8080 7D80
l[0]=37 37 36 38 37 37 37 37 37 37 37 37
l[1]=3B 37 36 37 37 37 37 37 37 37 37 37
l[2]=37 37 37 37 37 37 37 37 37 37 37 37
l[3]=37 37 37 37 37 37 37 37 3B 3B 37 37
l[4]=37 37 37 37 37 37 37 37 3D 3D 3D 3D
l[5]=43 43 43 43 43 43 43 43 43 43 43 47
l[6]=47 47 47 47 47 47 47 47 47 47 47 47
l[7]=47 47 47 47 47 47 47 47 47 47 47 55
l[8]=55 55 55 55 55 55 55 55 55 55 55 5C
l[9]=5C 5C 5C 5C 5C 5C 5C 5C 5C 5C 5C 5C
l[A]=70 70 6D 6D 6D 70 6D 6D 70 6D 70 70
l[B]=7E 7E 7E 7E 7E 7E 87 87 87 7E 7E 7E
n[0]=22 2F 48 64 81 92 9D A1 A2 A2 2B 21
n[1]=22 2F 46 62 7C 8F 9B 9F A0 A0 2A 21
n[2]=23 2F 44 5F 73 89 94 9A 9B 9D 28 26
n[3]=2A 30 3D 56 6A 80 8B 93 97 98 23 26
n[4]=29 2E 3B 53 66 7B 86 8E 93 94 1F 24
n[5]=25 2C 39 51 64 78 83 8B 90 92 1E 1C
n[6]=1E 27 35 4E 5F 6F 7C 83 87 8A 1A 17
n[7]=19 20 32 4C 5E 6B 74 79 7C 7E 14 12
n[8]=15 1C 2F 4A 5A 64 6A 6E 70 74 0F 0E
n[9]=10 17 2C 43 50 58 5D 62 66 68 09 0C
n[A]=0E 14 29 3B 46 4D 52 55 57 5A 04 0B
n[B]=0B 0E 24 30 38 3D 40 43 46 48 00 04
k[0]=14 23 32 4B 5A 64 7D 96 AF C8 E1 FF
r[0]=07 0C 0E 14 19 1E 25 2B 36 41 4A 4B
h[0]=04 10 08 02 01 00 40 00
h[1]=00 00 00 00 00 00 00 00
h[2]=00 00 00 00 00 00 00 00
b[0]=FF 32 00 00 00 1E 20 12 12 12 12 12
t[0]=12 1A 0E 06 04 02 00 00