I'm going to help in conversion from B&G MS to VEMS in friend's n/a Jetta 16v.
- 1.85L 16v, 136Hp stock + tube header, base engine KR, with ABF intake
- 4 cyl fuel injection, Hi-Z injectors
- Ignition with distributor, probably will go to wasted spark later
- PWM controlled idle valve
- 1xWBo2
- trigger from hall in distributor, 1 pulse/cylinder
Shopping list:
- 1 x GenBoard v3.2
- 1 x Econoseal36-PCB
- 1 x Econoseal36-Wire
- 1 x Econoseal18-PCB
- 1 x Econoseal18-Wire
- 1 x Alubos1600
- 1 x Alubos EC frontplate transparant
- 1 x Alubos Endplate transparant
- 2 x Alubos gasket
- 9 x FETs Injector driver, WBO2 heater driver (FQFP..)
- 5 x Ignition driver (IGBT)
- 1 x Ignition driver insulator sheet
- 1 x 2.5 bar MAP sensor
- 1 x Wideband connector
Information hunting
Let's assume one who never before has browsed through wiki has just got his V3.2 order. He might end up wondering what to do next? Does he need to solder something by hand? A little searching brings following pages:
- BuildProcedures/SectionThree
- GenBoard/Manual/InitialTesting/VerThree contains some information about the hardware to check
- GenBoard/VerThree/Testing contains same kind of information
- GenBoard/Manual/WBSensorControllerCompleting
- Some information is collected to the StepByStep page
So there is something to start. Maybe a proper step-by-step guid is needed, I'll try collecting the issues to a separate page from this exercise.
31.05.2005
Severe problems keeping the engine running nicely. Tried STABLE1_0 with config below, engine hardly runs. Same SW & config with older compiler and car runs almost nicely, but ign advance is for some reason limited to ~24degrees and changes in ve table doesn't seem to affect AFR at all..
22.05.2005
Car is now running, both fuel and ignition (dummy with distributor). Latest config dumps from board with STABLE1_0 firmware (20.05.2005)
09.05.2005
It's alive. Engine was running yesterday, board was only delivering fuel. Latest config files:
12.04.2005
Problem below was solved by updating a perl. With perl v5.8.6 make_ini.pl works smoothly.
Yesterday we made some initial tests in the car. MT configuration started to look somehow acceptable after a couple of hours, basically using old configuration from B&G MS. However TPS readings were not ok, values were either 16% at idle or by adding some throttle value jumped directly to 100%. In the LCD TPS values were ok.
11.04.2005
Some problems with perl. I use a activestate perl under Win: This is perl, v5.6.1 built for MSWin32-x86-multi-thread
When trying to run perl bin\make_ini.pl global.h doc\megatune\config.xml doc\megatune\vemsv3.ini I get an error message\n
"strict" is not defined in %XML::Simple::EXPORT_TAGS at C:/APPS/Perl/lib/Exporter/Heavy.pm line 75
Exporter::heavy_export('XML::Simple', 'main', ':strict') called at C:/APPS/Perl/lib/Exporter.pm line 45
Exporter::import('XML::Simple', ':strict') called at bin\make_ini.pl line 10
main::BEGIN() called at C:/APPS/Perl/site/lib/XML/Simple.pm line 10
eval {...} called at C:/APPS/Perl/site/lib/XML/Simple.pm line 10
Can't continue after import errors at bin\make_ini.pl line 10
BEGIN failed--compilation aborted at bin\make_ini.pl line 10.
I tried to download XML-Simple from activestate and installed it ppm install XML-Simple.ppd without any warnings etc. but obviously something is still wrong. Any hints?
04.04.2005
Board/case assembly is now mostly completed after some not-so-active period.
- Partially commented configuration files added here. These are not in any proper shape yet, mostly copied from GRM's config but will update once I get to the some real business.
03.03.2005
Completing of the controller begins.
Although board has a most of the parts already soldered on it, a few components still needs to soldered by hand.
- Injector driver FETs (TO220)
- Ingition IGBTs (TO220)
- WideBand LSU4 sensor heater driver (we use TO220 FET, same type as for injector drivers; except the WBO2 channel has no onboard place for flyback diodes)
There are also several items to check before even thinking to plug the board to the car.
- items to check listed here..
01.03.2005
Ordered items arrived
more details will follow..