VEMS Home Products Documentation Wiki Webstore
WikiHome ProjectPage DocsPage UnderDevelopment MembersPage SiteIndex RecentChanges Preferences
MembersPage/Koskar (2011-08-16 14:26:22)

Greetings from Finland!

My project car is Ford Escort Mk4 -87

Plans to season 2011: Install VEMS and throttle bodies

On July 2010 I got it to the dragstrip and results are: ET 14,32 s and speed 158,73 km/h

On August 2010 we got it to the dyno and results are: 129,9 Kw and 231,3 Nm.

[Escort Mk4]

Engine:

- Ford Galaxy -99 2.3i 16V engine block and cylinder head

- Ford Escort RS2000 -92 cams, exhaust header and intake manifold

- Ford Escort Cosworth T25 fuel pressure regulator (3,5bar)

- Davies Craig electric water pump and controller

- Ford Escort RS2000 ECU (EEC-IV) with Collins chip and EDIS4 with dual coils

[Engine bay pic in Botniaring Race Cirquit 2009]

My VEMS history :)

I build one VEMS project in 2008, but I sold it forward because I didn't have time to tune it. So it's time to try again!

Old wiring harness and ECU: [old harness]

VEMS external hardware

Injectors: Bosch 0 280 155 504 (~280cc/min@3,5bar?)

Coils: Ford dual coils

Coolant sensor: maybe GM because resistance range is suitable and it's got correct thread

Intake air sensor: GM for same reason

Primary trigger: Ford VR sensor

Secondary trigger: Ford VR sensor, reading exhaust cam at cylinder 4 (I'm not sure do I use this at the beginning at all)

TPS: Keihin TPS (stock Suzuki GSXR1000 K2)

LCD: 20x4 black/green with inverted colors

Lambda: Bosch 057

VEMS related shopping list

Soon I will make order to VEMS shop and I have allready collected some VEMS related items to my project (LCD, knock sensor and wiring harness stuff).

--> Done

Products

1 x GenBoard v3.6

- Ship start: 2 weeks 247.30EUR

1 x Alubos1600

- Drill-count: 6 27.04EUR

1 x Alubos EC frontplate

- Drill-count: 0 15.97EUR

1 x Alubos Endplate

- Drill-count: 4 5.84EUR

2 x Alubos gasket 4.14EUR

3 x clamping plate 7.89EUR

1 x Additional VR or Coil interface 3.99EUR

1 x Econoseal18-PCB 9.87EUR

1 x Econoseal36-PCB 13.89EUR

1 x Econoseal18-Wire side 9.90EUR

1 x EconoSeal36-Wire side 16.70EUR

1 x Wideband connector

- With wire: without wires 5.60EUR

1 x Idle stepper motor driver 3.00EUR

4 x Ignition driver 14.64EUR

1 x Ignition driver insulator sheet

- Size: 3lines 1.90EUR

9 x Injector or WBO2 heater driver 17.10EUR

1 x PTC fuse 0.71EUR

1 x Throughole Diode

- Model: 30V flyback 0.38EUR

1 x Throughole Diode

- Model: 18V unidir 0.43EUR

2 x VEMS sticker

- Color: white 0.56EUR

2 x VEMS sticker

- Color: red 0.74EUR

1 x VEMS sticker

- Color: metallic: silver 0.45EUR

Total: 412.94EUR

VEMS ECU assembly

Got ECU #3397 [Econoseal connectors soldered] and [underside]

[Black/green inverted LCD screen] and [LCD power on]

[LCD cable grommet and MAP-tube panel mount]

Is this 30V Flyback done correctly? And how about that 4+4 ignition setup. I use EC36 pins 34 and 36, other two IGBT-outputs are now shorted to GND and other 4 without IGBT:s are now connected to logic level.

[MAP, LCD-header, Flyback] and [underside]

Are these wires OK? Especially that 2nd VR from EC36-13 to 2nd LM1815. I measured that EC18-6 (Ch6) and EC18-12 (Ch7) already have pullup resistors (R85 and R86) to +5V.

[2nd VR, TX+RX, Analog Ch5/6/7 and Knock]

Connection from laptop USB -> Belkin F5U109 -> VEMS is working fine =).

[VEMS + LCD + Vemstune running!]

Some new pics and short video (added 16.08.2011)

[Analog inputs]

[VEMS wiring harness]

[Trigger log with 36-1]

[Just some pic of enginebay]

[Short video of second startup]

Questions and answers

1. I want to be sure with primary trigger config. So, when using 100% same 36-1 triggering that Ford EDIS use, what are correct settings?

--> Thanks for advice :)