Navigation
- Main MembersPage/KoabiBrooks
- Ignition MembersPage/KoabiBrooks/Idle
- Ignition MembersPage/KoabiBrooks/Ignition
- Injection MembersPage/KoabiBrooks/Injection
- Trigger MembersPage/KoabiBrooks/Trigger
- Wiring MembersPage/KoabiBrooks/Wiring
- Q&A MembersPage/KoabiBrooks/Questions
Current Status
Hooking up idle stabilizer valve. Please see the new idle section for details.
Learning how to tune...info below is pretty outdated - will update soon.
Config: http://koabi.lazyslacker.com/VEMS/logs/20071201config.txt
Tables: http://koabi.lazyslacker.com/VEMS/logs/20071201tables.txt
MSQ: http://koabi.lazyslacker.com/VEMS/logs/20071201megasquirt.msq
Datalog: http://koabi.lazyslacker.com/VEMS/logs/20071201datalog.xls
My goals
- To have control over engine management
- Make car reliable (near stock levels?)
- Learn about what makes all these variables work together
- NOT TO BLOW UP THE MOTOR
Car Specs
- 1988 Volkswagen Scirocco 16v
- Suspension
- H&R coilovers
- Poly bushings
- Engine
- ABA 2.0l 4 cylinder motor (From OBDI Jetta or Golf)
- PL 16v head (From 1.8l 16v Scirocco)
- Thottlebody with TPS (From automatic Corrado - bolts on)
- Turbo T3 .60/.48 (From ~'84 Ford Thunderbird)
- Gillis boost controller (Manual screw type)
- Intercooler
- 48# high z injectors (correct if wrong - high z meaning constant voltage to open is what I am assuming)
- Transmission
- 020 with shim kit, bolt kit, still a timebomb
VEMS SETUP
I am going with v3.2 assembled. Here is the current plans, which are subject to many, many changes.
Components
- Sensors
- Intake Air Temperature (IAT)
- GM #25036751
- Manifold Absolute Pressure Sensor (MAP)
- 2.5 bar (on board ECM)
- 1 Wideband oxygen sensor (WB02)
- Bosch LSU4
- 1 knock sensor (engine can accept 2, so perhaps I will eventually use 2) - not yet implemented
- Exhaust Gas Temperature sensor (EGT) - not yet implemented
- K Type
- Throttle Position Sensor (TPS)
- From automatic Corrado
- Fuel Pressure Sender - not yet implemented
- Probably the one at the VEMS webstore
- Boost Controller - not yet implemented
- Also through the VEMS webstore
- Intake Air Temperature (IAT)
Ignition and Injection Setup
- Crank trigger from ABA code motor - I won't be using a Hall
- VR std 60-2 VAG wheel on ABA crank. Those using different blocks may have to use external setups. See MembersPage/DerrickScirocco
- Part # 021 907 319 B
- VR std 60-2 VAG wheel on ABA crank. Those using different blocks may have to use external setups. See MembersPage/DerrickScirocco
- Wasted Spark Ignition
- 4 output coilpack from 99 2.0 8v VW - new beetle for sure, AEG engine code (this way I can use my stock plug wires)
- Part # 032 905 106 B
- 4 output coilpack from 99 2.0 8v VW - new beetle for sure, AEG engine code (this way I can use my stock plug wires)
- Sequential Fuel Injection (apparently it's an easy change toggling batch -> sequential, as long as you have the injectors wired separately)
The ECU (which apparently is a v3.2 board has this mod using 0 ohm connections):
Useful Resources
Crank wheel trigger generator: http://koabi.lazyslacker.com/VEMS/cranktriggers.php
GrmRacer's install guide (note injector flyback is accidentally omitted from the pinout) FIX THIS LINK: http://www.starshadow.com/~koabi/carstuff/VEMS/Information%20to%20setup%20your%20VEMSv3.htm