Navigation
- Main MembersPage/KoabiBrooks
- Ignition MembersPage/KoabiBrooks/Ignition
- Injection MembersPage/KoabiBrooks/Injection
- Trigger MembersPage/KoabiBrooks/Trigger
- Wiring MembersPage/KoabiBrooks/Wiring
- Q&A MembersPage/KoabiBrooks/Questions
MAIN PAGE
I have an '88 Volkswagen Scirocco
My goals
- To have control over engine management
- Make car reliable (near stock levels?)
- Learn about what makes all these variables work together
- NOT TO BLOW UP THE MOTOR
Car Specs
- Suspension
- Eibach Sportline Springs
- Tokico Shocks and Struts (for now)
- Poly bushings
- Engine
- ABA 2.0l 4 cylinder motor (From OBDI Jetta or Golf)
- PL 16v head (From 1.8l 16v Scirocco)
- Thottlebody with TPS (From automatic Corrado - bolts on)
- Turbo T3 .60/.48 (From ~'84 Ford Thunderbird)
- Gillis boost controller (Manual screw type)
- Intercooler
- Fuel Injection from G60 Corrado (CURRENTLY)
- 48# high z injectors (correct if wrong - high z meaning constant voltage to open is what I am assuming)
- Transmission
- Stock time-bomb
VEMS SETUP
I am going with v3.3 assembled. Here is the current plans, which are subject to many, many changes.
Components
- Sensors
- Intake Air Temperature (IAT)
- GM #25036751
- Manifold Absolute Pressure Sensor (MAP)
- 2.5 bar (on board ECM)
- 1 Wideband oxygen sensor (WB02)
- Bosch LSU4
- 1 knock sensor (engine can accept 2, so perhaps I will eventually use 2) - not yet implemented
- Exhaust Gas Temperature sensor (EGT) - not yet implemented
- K Type
- Throttle Position Sensor (TPS)
- From automatic Corrado
- Fuel Pressure Sender - not yet implemented
- Probably the one at the VEMS webstore
- Boost Controller - not yet implemented
- Also through the VEMS webstore
- Intake Air Temperature (IAT)
Ignition and Injection Setup
- Crank trigger from ABA code motor - I won't be using a Hall
- VR std 60-2 VAG wheel on ABA crank. Those using different blocks may have to use external setups. See MembersPage/DerrickScirocco
- Part # 021 907 319 B
- VR std 60-2 VAG wheel on ABA crank. Those using different blocks may have to use external setups. See MembersPage/DerrickScirocco
- Wasted Spark Ignition
- 4 output coilpack from 99 2.0 8v VW - new beetle for sure, AEG engine code (this way I can use my stock plug wires)
- Part # 032 905 106 B
- 4 output coilpack from 99 2.0 8v VW - new beetle for sure, AEG engine code (this way I can use my stock plug wires)
- Sequential Fuel Injection (apparently it's an easy change toggling batch -> sequential, as long as you have the injectors wired separately)
Rewiring after killing an injector wire due to poor wiring
The ECU (which apparently is a v3.2 board has this mod using 0 ohm connections):
EGO Correction
I've enabled EGO correction to compensate for a rough VE table. This is the easiest method until I can get someone to drive the car while i learn how to adjust the VE table on the fly. It seems that EGO correction is not being turned on consistently and I don't know how to interpret what I see. What I feel is the EGO messing with small part throttle situations causing the car to hesitate. At full throttle conditions I don't think correction is being used. Feedback is appreciated.
Log: http://koabi.lazyslacker.com/VEMS/logs/datalog200612091533.xls
Config: http://koabi.lazyslacker.com/VEMS/configs/20061209config.txt
Tables: http://koabi.lazyslacker.com/VEMS/configs/20061209tables.txt
Useful Resources
Crank wheel trigger generator: http://www.starshadow.com/~koabi/carstuff/cranktriggers.php
GrmRacer's install guide (note injector flyback is accidentally omitted from the pinout): http://www.starshadow.com/~koabi/carstuff/VEMS/Information%20to%20setup%20your%20VEMSv3.htm
Comments
Updated firmware to 1.0.53
what a 17 psi spike?! no wonder 1st gear had no traction.
Problems below have been resolved:
- I can't get the ALS SW indicator to be switched off in MT. The car drives normally, so all seems to be well, but it would be nice to have the indicator off.
- Try to set "Input Channel used" to "old: SDA" under ALS-settings. The channels 0-7 consider 0V as on and +5V as off, that's why they need a pullup-resistor to +5V. Note, this also works for the Launch control inidicator
- Also I am having weird accel enrichment.
- Apparently 0.2ms enrichment duration isn't enough - problem resolved
config: http://www.starshadow.com/~koabi/carstuff/VEMS/configs/20060926config.txt
tables: http://www.starshadow.com/~koabi/carstuff/VEMS/configs/20060926tables.txt
MT MSQ: http://www.starshadow.com/~koabi/carstuff/VEMS/configs/megasquirt200609262023.msq
log: http://www.starshadow.com/~koabi/carstuff/VEMS/logs/datalog200609262006.xls