Status: V3.3 Serial #1973 up and running, but with many issues.
Initial Issues:
1) P259 Ch5 used for Fuel pump Relay trigger, this would work when priming. But with the engine cranking, the relay would not activate. I later changed the output to Inj 5 (Ch. 4) and it worked OK.
2) Tach output (500 ohm pullup from Webshop) works, but the Tach will sporadically jump up very high, example jump to 4000 rpm at idle instead of 1000. I changed the Pull-up to 100 Ohms, but did not fix.
- 1000 Ohm works with most audi gauges. It might be something software / config related. Please publish mcd / mct dump (and what firmware you use). Check other outputs (maybe 2 functions configured to same output?)
- Link to dumps below - look down 10 cm :)
3) LCD screen will display normally after start-up. But after a few minutes the LCD data will get scrambled (? marks, data numbers and letters all over the place)
4) Car was running and driving, for about 6 hours of total run time. Several runs were made to 240 kpa(absolute) boost.
Then injector #1 (Ch.0) stuck on during a 1-2 gear power run. Output dead short to Ground. This is most often caused by a flyback connection problem. The FETs can service 2A all day long. But they die above 60V. Can cause other serious problems.
- flyback checked out with ohm-meter before and after install.
- curcuit is thru wiring harness (O2 sensor plug two wires joined) - fuel pump relay (two terminal 87 circuits) - to ECU
Took box apart to replace FET, decided instead to change wire to another injector output (Inj 6, Ch. 5).
Engine started and ran fine. Made a couple boost runs to 200 to 210 kpa.
But when making more runs at 220-240 kpa, the ECU "cuts out" and engine stumbles badly. (ecu loses communication, and you can see this in Megalogviewer when you graph the "time" and "seconds".
Comments/Background
- Is it possible that some of these issues are related? or caused by static damage? (I had to take the ecu apart 4-5 times over the course of the engine startup.)
- most likely related. If you touch the case first it's unlikely to cause static damage. The dead FET suggests flyback connection problem, and other problems might be related.
- OK I will do that first always. As a note, all problems are listed in order of occurance, tach and fuel pump relay problems existed before FET damage, and "cutting out" was after.
- most likely related. If you touch the case first it's unlikely to cause static damage. The dead FET suggests flyback connection problem, and other problems might be related.
- Flyback and Grounds checked out OK visual and resistance .1 to .3 Ohm.
Is it possible that somehow ECU is powered down while injectors are still powered ? Or flyback wire does not go to injector common directly but via some relay or other indirect method ? (measures low ohm, but disconnects for short time in certain cases like powerdown, that can damage injoutputs to fail later).
- Yes - Possible. ECU controls Fuel Pump Relay via Inj Ch4.
- Relay may have possible Diode-shutdown delay?
- Fuel Pump Relay other 87 circuit supplies injector power TODO: upload diagram
In any case, we recommend that you fire a warranty replacement order with same specs (or slightly more generic one). But best to investigate carefully before swapping. It seems you've measured carefully though.
- Fuel injectors are High-Z 1000cc, Bosch re-made in USA.
- can you measure resistance ? Everything we found between 727cc/min and 1550cc/min were low-Z
- injectors measure 12 Ohm.
- can you measure resistance ? Everything we found between 727cc/min and 1550cc/min were low-Z
- If Rinj >= 5.5 Ohm, can we purchase these injectors (new ones. 100 .. up to a few hundred) ?
- Yes - will email the contact information to webshop.
Dumps
http://www.vems.hu/files/KevinBlack/Jake%20W%20Issues2.rtf
Wiring
http://www.vems.hu/files/KevinBlack/Jake%20W%20AEB%20PnP%20Wiring.xls