Overview:
Car is a 1979 Volvo 242 with a 1995 Volvo 850 Turbo engine (B5234T).
Some details on the car:
- Inline 5-cyl., 2.3l, turbocharged (TD04H-15G), 4 valves per cylinder. The engine is essentially stock, save for a new (OE Volvo) intake manifold and 350cc injectors. At 15psi on the current setup I flow fuel for approximately 250bhp.
- VEMS 3.3 will replace the current setup of: MSnS-E 029y4 on a V3 PCB with sequential COP, batch fire injection, boost control, fan control, tacho output, two-step, and a Just Another Wideband (JAW).
VEMS Setup:
Apart from the standard sensors (MAP, CLT, IAT, TPS), I'm planning on setting up the VEMS with the following major functions:
- Sequential coil on plug
- Sequential injection
- Single channel wideband and EGT
- Dual channel knocksense
- Fan control, boost control, two-step, tacho output, shift-light, 20x4 LCD
Trigger settings:
The engine comes from the factory with a 60-2 wheel/VR sensor on the crank and a single tooth wheel/hall sensor on the cam.
Goals:
My initial goal with this install is to overcome the limitations of Megasquirt (some of which I have reached, others not), putting me in a much better position to take the car to the next level. Also to have a good time with it, and possibly learn something useful along the way.
Shopping cart:
I have put together a list of items to be ordered from the VEMS Webshop. Ideas, comments, or suggestions are welcome.
- GenBoard v3.3
- Injector or WBO2 heater driver (8, one for each injector, one for WBo2 heater, one for boost control, one spare)
- Ignition driver (2, running ignition in 2+6 configuration)
- Power Flyback - With wire
- Dual channel knock sensor interface (do I need this, or is it included on the board already?)
- 250-400 kPa MAP sensor - MAP connection 400kPa bare - Supply 5V (webshop is somewhat unclear, is this the correct map sensor?)
- - - -
- Alubos1600
- Alubos gasket
- Alubos Endplate
- Alubos EC frontplate
- Econoseal18-PCB
- Econoseal36-PCB
- Econoseal18-harness
- Econoseal36-harness
- Wideband connector - With crimped wires
I have decided to purchase the un-assembled GenBoard for a few reasons: I'm doing this as much for the learning experience as for the VEMS feature-set. If I wanted a 'plug-and-play' system I would buy a Haltech or Motec. A more minor motivator is the lower price.
I will be purchasing power resistors and an LCD seperately, as I can find both for much lower price locally.
Sections: (most of these are incomplete, will continue to add info and break into sections as time permits)
Crank and cam sensors/settings MembersPage/KarlBuchka/Trigger
(The crank setup is a 60-2 trigger wheel built in to the flywheel using a VR sensor. Cam setup is single tooth wheel using a Hall sensor. Firing order is 1-2-5-3-4. MembersPage/RonnieH has set up VEMS on a very similar motor also with seq. COP. Should be able to lift his trigger settings if code hasn't changed too greatly since he last update.)
Sensors and inputs MembersPage/KarlBuchka/Sensors
Fuel (Injectors, VE, lambda, enrichments) MembersPage/KarlBuchka/Fuel
Spark (Coils, Spark advance) MembersPage/KarlBuchka/Spark
Outputs/ancillaries MembersPage/KarlBuchka/Outputs
(Fan control, boost control, shift light)