Successful conversion to VEMS Genboard 3.2 on my race spec 1985 VW Golf.
Pictures and some info:
http://proton.shadowflux.com/vwracing/
More pictures (updated often):
email james at shadowflux dot com
While browsing the net I came upon this thread about someone using 034EFI on their turbo VR6 VW Golf. The 034EFI setup looks very nice. The thread is located at: http://forums.vwvortex.com/zerothread?id=2470106&page=6
Progress 29 July 2006:
Firmware r045
Config at http://proton.shadowflux.com/vems/config/megasquirt200607291807.msq
Remember to post mcd / mct dump (if you expect someone to review).
- generate-config.bat misses a few config variables including
- toothrel_normal
- toothrel_missing
- fuelcut_min_kpa
- fuelcut_max_kpa
- tach_channel
- tach_div
- shiftcut_conf
- shiftcut_channel
- shiftcut_time
- softrpm_rpm good candidate to limit RPM
- crank_minper can also limit RPM if too high (use 0x30 = decimal 48)
Maybe one of these vars has something to do with my artificial rpm limit at 6000 rpm? Engine will NOT rev above 6000 rpm. Seems like fuel is being cut, but I can't tell for sure.
Was having trouble with ego correction going wild. Fix was to increase injector opening times and reduce req_fuel from 9.2ms to 6.6ms. Now getting realistic ego correction and ve learning is working as it should.
Progress 9 July 2006:
Firmware r045, Megatune for 1.0.36
On conversion from firmware r023 several options were left unset in config which threw everything off quite a bit. Be sure to review all pages and set config accordingly. Enabling antilag and launch by accident will prevent engine from running.
- Fuel cut was defaulted to 0kPa which confused me for a few minutes when it would fire while cranking but never start.
- Autotune still wants to drag my VE values down to zero, even though they VE figures are fairly accurate. Anyone else experiencing similar problems?
- Spark cut idle control works nicely, but now there are several pages for idle settings. Consolidation possible to avoid confusion?
- Having trouble spinning motor faster than 6000 rpm. Can someone review my config (good03.msq) and recent datalogs and give some comments please?
- We have this problem too with 1.0.36 firmware: when reaching something like 6000rpm, the engine shuts itself off. And then turning the starter, acts normal until you rev it more than 6000.... PeepPaadam
Progress report (Nov 11):
Firmware r023
Starts and runs! Idles fairly smoothly with only set-screw holding throttle body at 4-5% open. Drove around a little bit, runs very well and all parameters look good. Accelerates much harder than when K-Jet was running the show, until it gets to the sections of fuel map I haven't tuned. I'll be reviewing logs today, updating tables and doing more testing, provided the rain stays away. Thank you, everyone, for your help!
- Notes:
- * VE table values had to be doubled even though req_fuel was set at value recommended by req_fuel calculators.
- * Top dead center after trigger was retarded by 30 crank degrees.
- * Use MegaTune to enable/disable features (misc_out, boost control, iac, etc). Disable values in config.txt inconsistent between feature channel outputs.
- * LCD display is cutting out, displaying with strange offsets, otherwise acting funny. Vibration getting to headers or wiring elsewhere? Will test.
Config
Latest/revised comments config: MembersPage/JimW/Config
Notes about subsystems (to verify/justify config variables) on pages below
- MembersPage/JimW/FuelSystem
- MembersPage/JimW/InputTrigger
- MembersPage/JimW/IgnitionOutput
- MembersPage/JimW/AirFeed
- MembersPage/JimW/Wiring
- MembersPage/JimW/Sensors
My Genboard and LCD display:
