I'm Automotive Engineering student from Finland.
I were developing four-cylinder BMW M10 2.0 '77 turbo engine as my engineering/diploma work, but I have changed my work to Honda D16Z6 SOHC-VTEC All-Motor project. Reasons for this are too high costs for a student, and I definately need a new (and ofcourse better and more powerful) engine to my daily driver Civic.
I'm still gonna use GenBoard/VerThree in my Civic, and replace MegaSquirt I have on it right now.
Check my MembersPage/JanneMantyla/PictureGallery ! WARNING! lots of high-quality pictures on same page! Should I do this somehow other way?
D16Z6 Engine info and plans
- Bore 75mm, stroke 90mm
- Honda PM7 high dome pistons, 12:1 compression ratio
- ARP head studs, rod, flywheel and pressure plate bolts
- Reshaped stock valves (30/26mm)
- [Crower Stage 3] cam, Crower valvesprings and Ti-retainers
- 42mm ITB setup. Honda CBR954RR throttlebodies and injectors (hi-z), my own designed/made aluminum manifold. Intake total lenght 230mm.
- My own design 4-1 anti-reversion header(lenght 660mm/26", merged collector), 2.5" exhaust.
- ACT XTSS clutch Xtreme pressure plate, performance organic disc
- ACT XACT ProLite 3,8kg / 8.4lbs flywheel
D16Z6 sensors etc
- Original Denso IAT/CLT sensors (values equals Bosch)
- Original TPS and MAP. I've heard it works with 0.8bar, so propably 180...200kPa range?
- Maybe VAG 1.8t 20V active COPs. These are cheap, and suits fine to Honda head. Another alternative could be CBR600 F4i passive COPs. Bosch wastedspark is powerful, but not as sophisticated, and needs ignition wires as expensive as VAG COPs.
- Honeywell 1GT101DC Hall-sensor at crank. One trigger pulse/event. Maybe 4-1 or 12-1 wheel decoder in future
- Propably some camtrigger. Original distributor has two VR-sensors on it.
- Bosch LSU-4 WideBand sensor
- Blue 4x20 LCD
- EGT K-type thermocouple
BMW Engine plan, somewhere in future:
- Bore 90.0mm, stroke 80.0mm
- Valves 46mm intake, 38mm exhaust
- Cylinderhead BMW E12 2.0 '78
- Crank BMW Original forged steel, nitrided
- Camshaft Dr.Schrick 304 (Adv. duration 304 deg. lobe angle 108 deg. lift 10.7mm)
- 4x45mm Individual Throttle Bodies
- Suitable big turbocharger, Garrett GT3582R dual ball bearing unit looks very neat
- Intercooler core size 600x300x75mm
Engine management, sensors etc for BMW (I already have these, except the big injectors):
- GenBoard/VerThree V3.2, loaded with ~all I/O options
- 8 injectors (four small in ITBs, 4 big (~900cc) in the end of velocity stacks)?, GenBoard/Manual/PowerFlyback
- all 8 injectors connected to separate injector output channels, so sequence can be reconfigured from software ? (or some shared?)
- I was thinking to connect each of them to individual outputs. Not sure yet about the configuration. Full sequential adds complexity(CamTrigger), but would make life easier for GenBoard. My intention is that the first four, small ones, operate at low MAP/load/cruise, and big ones operate at under boost/WOT.
- Wastedspark ignition, [Bosch Motorsport 0 221 503 407] double fire coil
- Motorola MPXH6400 MAP-sensor (external, on firewall)
- WideBand O2 sensor Bosch LSU-4
- BoostControl
- CLT sensor Bosch 0 280 130 026
- IAT sensor Bosch 0 280 130 085 (Fast, open-element)
- Blue 4x20 LCD and PS2 keyboard
- K-type thermocouple EGT
- Honeywell 1GT101DC Hall-sensor and 12-1 wheeldecoder at crankshaft