Hallo I am from Denmark and I am planing to use a V3.2 on my VW Golf GTI 8V.
MembersPage/HansK/IgnitionSetup
MembersPage/HansK/EgoReadingProblems
2005.07.16
Q.1) Does the MAPdot work fin, and should it be a certain firmware/megatune I use?
Q.2)When i open my Lambda Table in MegaTune (r18 and Firmware 1.0.12) the numbers are all wrong..
I can get the same numbers out of the board again with the Terminal-program as I put in.. But they don't show in MegaTune???
The numbers I put in the Tables-file was:
l[0]=4E 3B 39 38 38 38 3B 3B 3B 3B 3B 3B
l[1]=4E 3B 39 38 38 38 3B 3B 3B 3B 3B 3B
l[2]=4E 3B 39 38 38 38 3B 3B 3B 3B 3B 3B
l[3]=4E 3B 39 38 38 38 3B 3B 3B 3B 3B 3B
l[4]=4E 3B 39 38 38 38 3B 3B 3B 3B 3B 3B
l[5]=4E 3B 39 38 39 39 3F 41 41 41 41 41
l[6]=4E 3B 3B 39 3B 3B 3F 44 44 44 44 44
l[7]=4E 3D 3D 3B 3D 3D 3F 48 4E 4E 4E 4E
l[8]=4E 3F 3F 3D 3F 3F 41 48 4E 4E 4E 4E
l[9]=4E 41 41 3F 3F 3F 42 4C 4E 4E 4E 4E
l[A]=4E 41 41 41 41 41 44 4C 4E 4E 4E 4E
l[B]=4E 41 41 41 41 41 44 4C 4E 4E 4E 4E
Q.3) If I download the new Firmware 1.0.14 to the board, I want to to do some new testing on the table but now I mounted all the transistors in the box.. Should I just put a lightbulb on all the outputs or what to do?? What Firmware version can be recommended?
Please post your config.txt so that others can review and hopefullly learn (especially me ;) Thank you.
http://www.vems.hu/files/HansK/Config.txt
It is not in use yet so don't put too much in it, but you are welcom to give input.
2005.06.19
Q.1) I have a 2-pin idle-valve, but what settings should be used fore this.. PWM, ON/OFF?
Any solenoid works with ON/OFF. Only some work (well) with PWM.
- what is resistance ?
- anything known about original application? Does it have real idle-air control or just simple "fast-idle" ?
Does some one use the the same valve, and have a config-file that I can see or just some input to what settings to use?
Q.2) Is there some way to test the idle-output?
- which output did you choose in iac_sol_channel ?
- PWM type iac output can be tested with forced iac.position: mdi01..mdiff . Do NOT forget to set back to mdi00 (or reboot) after you executed the tests to revert to normal control.
- alternatively it can be tested like any other digital output, with mdh.. command. See GenBoard/Manual/DigitalOut/Table. In this case, do NOT forget to set iac_sol_channel=FF to prevent interference and set it back after the test.
2005.06.01
I got the new Megatune "mt-r014" and I tryed to use the firmware that was together whit it, but then I got no "output" on inj. or ign. and the the config and table was the same..?
No problem.. Just needed to chance secondary_trigger to "02" instead of "FF".