I have the CAN BUS mockup module from the shop.
https://shop.vems.hu/catalog/stm32f103mcp2515-p-213.html
By what means can I change the CAN output Id's, scaling, offset etc? Is it pre-programmed into via firmware or is there any way of changing the config and then rebooting?
I also received a USB stick
which has 4 wires
Yellow - SWDIO
Brown - GND
Orange - SWCLK
RED - 3.3v
Inside the module there is a 4 way header pin and also a micro USB connector.
Currently the 4 way header (GND, SWDIO, SWCLK) from the USB-
Programmed to convert aim => AUDI CAN-data, see SimpleCanMessages
- if different needed, what message ID, what exact data ? See CanBus
- CAN messages are not "1 dimensional", (not like a 0-5V that can be tuned with a pot); If the message is known and specified, it can be programmed; otherwise not.
Testing step 1
I´m only getting Id 0x280 @ 500Kbit @ 10Hz but nothing on it.
The ECU has RPM and is operating, but nothing is coming out on CAN at ID 0x280. What configuration does it have? If nothing how can I put a config on it?
If AIM is verified, See CanBus
I don´t have a Android phone to test the AIM out or a gauge but It looks like I´m not getting AIM out.
Definitely check that first (easy with a terminal, every 5th byte is A3).
- AIM is verified with a A3 every fifth byte. And the ECU has RPM and TPS but nothing on the 0x280 Id.http://www.vems.hu/files/CAN_testing/Aim%20out.txt
Is AIM out only available via second RS232?
Aim output stream is available via 1st or 2nd serial, but 1st is often used for VT, so 2nd serial is much more practical: see BroadcastDatastreamAim section: "Configure 2nd UART to send "5 byte stream" with datacontent matching the AIM"
I?ve got a aim2can module with analogs.
My problem is the input voltage range from a 0-5v sensor is only 0-3v with a factor of 1.5v till that point into the vems. This means I cannot properly use the sensors full range.
The ratio of actual sensor voltage to vems reported voltage is about 1.5 upto 3v, after that it starts changing as the module hits its max range
Multimeter >> VEMS voltage tested using a potentiometer
0.00 >> 0.02
0.50 >> 0.77
1.03 >> 1.57
1.48 >> 2.25
1.99 >> 3.01
2.51 >> 3.79
3.00 >> 4.52
3.52 >> 5.00
4.00 >> 5.00
4.52 >> 5.00
4.91 >> 5.00
If 0-5V input range is needed, simply divide by 1.5
- eg 4k7 series resistor, and 10k to GND (See VoltageDivider)
- Will the aim2can module ever be updated to have a native 0-5v range or will it always be stuck at 0-3.3v? Having to put an external voltage divider on all the analog channels is not a great way to go about things.
I?ve managed to double check the AIM output stream
Lambda is not being sent out anywhere.
See below
The Snip was with 0.96 Lambda value
The Top right Lambda was 1.83
There is 1831(Lambda 1.831) being sent on byte 3 & 4 but it never updates.
Can you test AIM module software and send me an update so I can get this working?
Can you tell me exactly where the Lambda should be(id and byte) so I can 100% verify it not working? From the pictures above there is no action.
Gunni