Power
| Power |
| Wire Color | Use | number in setup | ECIII pin |
| Black/Red | EFI Relay #1 | +13.8VBATT | 25 |
| Grounds |
| Wire Color | Use | number in setup | ECIII pin |
| Black | ground to CLT | GND | 26 |
| Black | power grounds | GND5 | 32 |
| Black | power grounds | GND5 | 21 |
| Black | power grounds | GND5 | 5 |
TPS
| TPS switch |
| Wire Color | Use | number in setup | ECIII pin |
| Red | Wiper | TPS | pin1 |
| Light Blue/Red | PWR | TPS5V | pin28 |
| Brown | common | GND | pin26 |
| Light Blue | Switch | | |
Injectors
| Injector |
| Wire Color | Injector | number in setup | ECIII pin |
| Yellow | Injector power | EFI Relay | |
| | Injector #1 | INJA | pin7 |
| | Injector #2 | INJB | pin19 |
| | Injector #3 | INJC | pin8 |
| | Injector #4 | INJD | pin20 |
Coils setup
| The pairs I will use so I can run wasted is |
| Wire Color | Transistor | number in setup | ECIII pin | cyl |
| ?? | Q16 | #0 | pin35 | 1,4 |
| ?? | Q21 | #1 | pin33 | 2,3 |
CLT
| Wire Color | Use | number in setup | ECIII pin |
| ?? | CLT | CLT | 14 |
| Black | Gnd | Gnd | 26 |
IAT
| Wire Color | Use | number in setup | ECIII pin |
| Yellow/Black | | MAT | 2 |
| Black | Gnd | Gnd | 26 |
CAM Trigers
| CAM Trigers use coex |
| Wire Color | Use | number in setup | ECIII pin |
| Ne | coex | TRIGG1_CONN | 27 |
| G1 | coex | TRIGG2_CONN | 13 |
| G- | shield | GND | 26 |
WBO²
ground the green coex to gnd
| WBO² |
| Wire Color | Use | ECIII18 pin | WBO² pin |
| ?? | PUMP(-) | 7 | 5 |
| ?? | PUMP(+) | 9 | 6 |
| coex | NERNST_CELL1 | 13 | 1 |
| ?? | HEATER1(-) | 18 | 4 |
| ?? | Power | N/A | 3 |
| Power will come from the old wire that went to the NBO² |
Tachometer
| Tachometer |
| Wire Color | Use | number in setup | ECIII18 pin |
| ?? | goes to cluster(tach) | STEP_B | 10 |
Knock
| Knock Use coex |
| Wire Color | Use | number in setup | ECIII pin |
| ?? | KNOCK1 | | 34 |
| Shield | Knock gnd | | 36 |
Fan
| Fan Reley |
| Wire Color | Use | ECIII18 pin |
| ?? | STEP_C | 5 |
Fuel Pump Power Control
| Fuel Pump |
| Wire Color | Use | number in setup | ECIII pin |
| Green/Red | relay | STEP_A | small#4 |
IAC
Need to add a flyback diode between the pins?
| Wire Color | Use | number in setup | ECIII pin |
| ?? | will be the IAC control | INJG | pin6 |
| ?? | will be the IAC control | INJF | pin18 |
| ?? | Switched power | N/A | N/A |
Check Engine Light
| Wire Color | Use | number in setup | ECIII pin |
| Green/White | ?? | ?? | ?? |
Serial Port
| Wire Color | Use | number in setup | ECIII18 pin |
| Red | RxD | RxD | 14 |
| Brown | TxD | TxD | 15 |
C BLACK firewall connector