Hi,
My projectcar is a 205 GTI with a 1.9 litre 8 valve engine. I turbocharged it some time ago and am now fully rebuilding/upgrading the engine to suit high boost. Have a look at my project webpage http://www.205turbo.nl
I;m looking into VEMS because I think it more advanced than the megasquirt i'm running now.
---
specs in a nutshell:
alloy 1905 CC wetliner engine
16 valve cyl head
Mitsu td05 16g turbo
--- update 18-08-05
Ok, got the vems all wired up. Everything seems to respond ok. Put in the 023 with megatune firmware version. (And used Dave Bruls' config files with small modifications.) And also megatune seems to work fine.
Will try to start the car one of these days.
- Only problem is the volt meter in Megatune. It gives 20 volt readings while battery voltage is 13 v.
- You probably missed to calibrate it, adjust battery calibration. Default batt_cal=0xBC (decimal 188) or so
- thanks for that!
- You probably missed to calibrate it, adjust battery calibration. Default batt_cal=0xBC (decimal 188) or so
Ok things are getting along quite nicely.
The engine turns.
I get an RPM sgignal
There is fuel coming out of the injectors
but still no spark. will have to look deeper into that. Running wasted spark. (bosch coil) there is +12v on the ignition drivers (00 and 01) but it seems they do nog get switched.
put the folowing line in tables.txt
h[2]=00 01 00 00 00 00 00 00
these are in the config.txt:
ignchmax=01
filled the ignition table
set the ignition settings as follows:
ignition outputs: 01..00
ignition driver type: DUMMY
ivert driver output Disabled
chargetime @ 14v 3.46
chargetime add @ 6v 4.18
set the trigger seetings as follows:
edge: rising
type: multitooth
Filtering: disabled
TDC after the trigger (deg): 62.0
number of teeth on wheel: 58
trigger tooth: 8
next trigger tooth: 30
Cranck min.period: 1280
angular with of tooth: 6
angular with of missing tooth: 18.
But I assume that to be quite ok because the RPM shows up (or is that a wrong conclusion)
set crancking advance to 20.00 degrees
Problem is there is no spark at all.
Checked the +12v to the coil (and up to the vems) and seems ok.
Any suggestions to where to start trouble shooting would be welcome.
- Publish full config, saved by mcd command.
- Try to compare your ignition related parameters with a working config, such as MembersPage/MarcellGal/EngineSwap .
- As the last chance, start again from the working config, only change what is necessary.
- check again if you missed something from GenBoard/UnderDevelopment/FirmwareChanges
- Eg. make sure secondary_trigger=02 is used ?
---
Small update: just used some leds to check if the igbt's get switched. but they don't...
---
Thanks to Daves' input the spark works. It was the secondary trigger that needed to be set to 02
---
Took it for a drive this day. But the engine ran verry lean (afr 1:16) and it appeared all the tables are ampty somehow in megatune. I had this problem with a more recent firware before. Ans switched to a bit older one that seemed to work fine. But now the tables are empty again. Does anybode have any idea hhow this could be fixed?
Working with tables.txt is not really an option when runing on the road.
ok, got the latest megatune version and the new .ini file. It seems to keep the tables now but doesn't start anymore though i saved the settings (with mcd in hyperterm) and used them in the new firmware
the pulse width megatune displays is 0 though the crancking pulsewith is set and so is the req_fuel (and all tables are filled with the right values)
any suggestions?