1.1.90 first check & How to install the 2nd VR Trigger?
Results by installing LM1815 to get secondary VR trigger :
- I followed the document named "Genboard v3
Check steps on GenBoard/Manual/InputTriggerHardWare
Also check sectrig options in [shop]
- currently sectrig=VR (now not same as auditrigger!!!), EC36pin13 is setup for VR input. EC18pin12 is an mcp3208 input
- the masking signal is pulled up with 2k7 to +5V internally
- earlier the 3-input (1 primary + 2 signal for secondary) auditrigger (without camHALL inverter): EC36/13 was the masking signal (if not pulled to ground, but left the internal pullup to pull to 5V - resulting voltage should be 3.5V or higher)
- than the VR input (earlier EC18/12) was used only
You can also deviate (eg. use shielded cable through endplate) but take note on this page. We can provide better help if we see your sharp photos.
If you split your MembersPage/FPhil page thematically (see MembersPage/DavidBlades for a good example) and agree to continue documenting the wiring and config you use (also thematically) shop grants you an assembled ECU free-of-charge with VR/VR, write in the order comment "MembersPage/FPhil offer by Marcell 2011-04-29".
Secondary trigger VR overview
The LM1815 circuit for the secondary trigger is same as for the primary trigger, which is built according to the LM1815 datasheet recommendations.
Since the sectrig pulsecount is lower (it never has to cope with the 135 tooth 10000 RPM auditrigger), higher capacitance can be applied in the filtering and the output timing circuit as well.
The LM1815 keeps the output pulled down to 0V, and releases for appr 50 usec (t=appr RC from R and C values) after the zero crossing negative-going edge on the input.
- The LM1815 output design is a bit weird! Inverted output would have been saner ! (for lower supply-current and better measurability) but that's how they made it.
- also, with the inverted output, the LM1815 output blob (on the bottom side of genboard) would not be necessary, the LM1815 would not disturb HALL signal.
- But the LM1815 (otherwise a good chip) works this way, and with VR setup the LM1815pin12 output must be connected to microcontroller input pin (SJ7 solder-blob on the bottom close, to the line of FETs). With HALL setup it must NOT be connected.
VemsTune generated maserati trigger signal
In recent (eg. 2011-04-26) VemsTune, Tools/Play trigger, type in "z012" or "Z012"
- even if not added to the combo selection, you can easily type in using the keyboard
- The difference between lowercase z and capital Z is polarity.
The sound-card is often sensitive with low-toothcount signals. So with ECU connected, verify in Tools/Analyze Trigger that the signal seen by ECU is same. Might need to play with mixer volume. Also, disable any 3D effects !
Done some 1.1.90 testing..
- Version 1.1.90 uploaded on my genboard (type 3.3?)
- (bought in 2005, sorry I do not have the SN here with me)
- config file is 2011.04.22-19-58-49.vemscfg
- VemsTune is 0.10.84 (2010.11.15)without the configlet Maserati Z012 and trigger play Z012. I was unable to find how to download the last April version.
Results by using my Maserati.biturbo.wav :
- Does not start, of course Camsync cannot work: my second trigger is Hall. Needs conversion to VR.
- camsync disabled -> full start FINE