I have access to wiring diagrams for any vehicle available in North American 1983-present. Sometimes I can cross it over to Rest Of World cars. If you need schematics for anything, feel free to email me. alandaeric at hotmail dot com
TODO: update all the pages to reflect uptodate status. Delete all old info, or move to a separat history page.
- MembersPage/EricN/BoardSetup-step by step of putting my board together
- MembersPage/EricN/WBSensor - Testing and config
- MembersPage/EricN/Trigger - inputtrigger
- MembersPage/EricN/Ignition - ignition advance, ignition output and coil related knowledge
- MembersPage/EricN/FuelPage - Injector and fuel setup and config
- MembersPage/EricN/Sensor - sensor info
- MembersPage/EricN/Config - complete config and tables
- MembersPage/EricN/BuildNotes : scraps of info not organinzed
ITS DEAD
Tried to start the truck the other day
- MegaTune comm works ?
- LCD works ?
- no rpm signal. What about wheel_error ? (Switch LCD to page 01 with mlp01 and check if W.. increasing ?)
- no fuel pump activity (untill I hit the brake pedal, then it wouldnt shut off) nothing working as far as I could tell.
- Put the ecu on my test bench, everything powers up and looks fine, all the sensors read properly, I can upload firmware, everything looks ok untill I try and do an mdh command. I noticed the fuel pump channel doesnt turn on. Tried some other channels, none of the P259 channels work at all, all the I259 and S259 channels are always grounded, mdh does nothing. All this happened after I uploaded the 1.0.23 firmware. The truck was running before but it was barely able to stay running, and was gradually getting worse but that may be related to playing with some settings. I reloaded 1.0.18 again. I can load my config and tables everything no problem so I assume the firmware side of things is all in tact.
- I went out to the truck to check the wiring, found 1 wire ripped out of ecu, the EC36 pin 26 ground wire. Connect the EC36pin26 ground ASAP!
- Ground and GND5 (and flyback) are the most important wires to have connected all times when the ECM is powered.
Also: TODO: update all the pages to reflect uptodate status. Delete all old info, or move to a separat history page. Marcell tried to review your setup, but couldn't tell what is uptodate because old information is left on the pages that shouldn't.
IT RUNS!!!
After months, no, make that years (since before v2.2 came out)of researching, I finally could not wait so I botched together a fuel pump system, installed my wire harness, plugged my v3.3 in and hit the key. Fuel pump running, smell fuel in the engine, but nothing. Then I turned the fuel pump off and cranked for a while figureing it was just flooded when KABOOM, I was sure my exhaust was dust, too bad for it. Shifted the firing order 180 degrees and add a touch throttle and vrooom. Ran like crap but stayed running as long as I kept a touch of throttle. Need to move it now from the front yard onto the driveway so I can weld up the O2 bung and start tuning.
SHOPPING LIST
Have: Everything
GenboardV3.2
1 x TPIC8101DW. Dual-channel acoustic knock sensor interface chip
1 x Stepper driver IC, package: DIP16
9 x FET: FQPF20N06L (FAI) 15A,
MY PROJECT
Ford 347 stroker- on hold,(taking to long to build car)
Temporarily putting it in a 61 404 unimog, mercedes 2.2l straight 6.
- Standard Honda map sensor (maybe)
- Standard Honda ect sensor
- Standard Honda air temp sensor
- No iac, just ignition advance idle control
- Bosch WB 02
- No knock sensor yet
- No egt sensor
- 24-1 vr sensor mounted in old distributer
- LS1 cnp coils
Will this VFD work easily??
http://www.vfdworld.com/techdocs/Noritake_CU20045SCPB-T23A_4x20_VFD.pdf
It's a serial VFD, it will not work. You need a paralell interface with a 44080 compatible command set. Note that VFD displays often have small incompatibilities with LCD displays even if they are listed as LCD compatible.
WISH LIST
- I would like to have a configureable speedo output. (not for my project)
- Drive by Wire, need some serious help with that one.