User page for megatune tuningsoftware
With the release details there is also some development info here.
Downloadable megatune and firmware matched and packaged releases
Changelog
- [VemsMT1.1.1-pre0.zip experimental prerelease]
- TODO: test [V3GUI] : a GUI-tool (zip for windows, but also available on linux, ask if you need it). This will replace .bat scripts. Functions:
- Upload/Verify firmware
- Upload/fetch config/table files
- Generate wav trigger sound based on trigger.ini file (reported to be buggy, might crash; will be fixed in next release)
- set chosen coolant/air temperature tables (EasyTherm - hexpatch way); will be implemented in next release.
- DONE: GenBoard/Manual/MatRetard (actually, firmware change without any megatune aspect)
- DONE: appear "MAP(load) mult" at another place where one would expect (at hybrid...RPM settings)
- DONE: h[1]
- DONE: ALS and launch input selection
- TODO: h[2] almost OK, but make sure MT resets bit0:2 and bit7
- maketables.exe should examine h[2] upper nibbles: if all are 0, than swap upper and lower nibbles to gracefully migrate to new h[2] semantics, where i259 outputs are 0x00,0x10...0x70 and s259 outputs 3..6 (stepper A..D) can be used for ignition with bit[1]>0 eg. 0x38,0x48,0x58,0x68)
- done ? merge changes in stable1_0 vemsv3.ini (curve-editor?)
- TODO: drop makeconfig.exe (and maybe all the .bats?) makeconfig.exe should not write unspecified vars as FF (done in svn, just need to be compiled)
- TODO: drop sh.exe
- [ VemsMT1.0.65-pre0.zip] has stable1_0 firmware (with recent stable1_1 changes merged)
- minor TODO: get rid of VEMS2 undefined (vemsv3.ini L326) error
- TODO: test [V3GUI] : a GUI-tool (zip for windows, but also available on linux, ask if you need it). This will replace .bat scripts. Functions:
-
[VemsMT1.0.69.zip] - Full package with firmware 1.0.69- Now includes generate-configWithWBO2Defaults.bat which ensures that the factory recommended wideband settings are correct. Does not effect unit specific (pump_pw_zero, nernstdc_target and wbo2_calibration) settings.
- [VemsMT1.0.53.zip] - Full package with firmware 1.0.53
- [VemsMT1.0.36.zip] - full package with firmware 1.0.36
- [VemsMT1.0.30rc3.zip] Renamed the full package for less confusion
- Lots of improvements in megatune, Curve editor (boost vs rpm table), plugins (Tools / Vemslogger Viewer), nicer Table Editor
- It is now possible to inactivate profiles according to your own taste, check the Profileactivation folder in the zip.
- Notifies user of which code is chosen
- temp calibration upload script
- readme.txt file
- improved .bat scripts
- minor changes in megatune dialogs
- please report errors on the IssueReports page
Instructions to make it work:
- download complete package above
- unzip to a directory of your liking
- use "download_config.bat" to fetch your current config from ecm or copy your existing config.txt and tables.txt to VemsMT-xxxx/config
- update your config (if required) with the config changes that may be there between the firmware version you currently used and the version you are about to upgrade to, see GenBoard/UnderDevelopment/FirmwareChanges for details on changes. YOUR CAR MIGHT NOT START OTHERWISE OR YOU MIGHT GET UNWANTED BEHAVIOUR !
- issue a "generate_config.bat"
- closely inspect the generated log files (config.log and tables.log) too see if you missed anything
- flash firmware your v3.X using "upload-firmware.bat" from the directory
- optionally run "tempsensor_upload.bat" to configure your temperature compensation tables (default is clt and iat = 2252).
- upload your tables.mtt and config.mtt to ecm using upload-config.bat"
- Reboot the ECM (cycle power)
- browse to the VemsMT-xxxx/MegaTune2.25 dir and execute megatune.exe
- select the profile that matches your firmware
- start tuning your engine
Developer section / Beta Ini files
All current MegaTune profile lockig and editing is done though svn
- mostly obsolete development info MegaTune/Development
Fero published some minor modifications with vemsv3.ini but almost useless published this way (more work to merge than redo)
- I've made all the modifications with the newest ini file from the firmware 1.1.11. Uploaded the complete pack. Everything is in that. Check it!: