Here you can link your report issues with your Genboard V3, firmware, tuningprogram or hardware problems.
Make your report on your MembersPage, and place link in the relevant section (with a "title", so it can be remembered easily). If you dont know the section, put it under "Unknown".
In the report, include a short entry and description + URL to your page, where the page contains:
- .vemslog or .vemscfg is absolutely essential to reproduce
- any report without these will be deleted. Add .vemslog or .vemscfg
- and besides these, (especially if a trigger problem, with new firmwares like 1.1.81) also a triggerlog (so the team can get a chance to reproduce and help to resolve the case).
- Note that newer firmwares have new trigger-settings in config bits that were previously "don't care". Bad settings of these will simply prevent triggering, so carefully check after uploading an 1.0.x or 1.1.7x or older config to a new 1.1.8x firmware)
- board version, serial Nr.
- firmware version
- MegaTune version (when MegaTune is used at all)
- intended config.txt (possibly commented)
- mcdmct.txt (captured output of Manmcdmct command.) This is the live config. Very important, since in a bad case it can be different from the intended config (if you used a global.h from a different firmware version; or there is a MegaTune configuration problem, etc...)
- description of the problem
- your investigation so far
- any ideas to proceed
The report, to be considered, must contain ALL necessary info. Without the necessary info, question-answer iterations are needed, so solution is delayed in the best case. If there is not enough info to reproduce, the report is neglected (especially if it contradicts experience). Re-post with the necessary info if you believe it holds.
Hardware: - usually wiring. These are normally answered even if you only use your MembersPage, but if you insist...
- ...
Config: please use your MembersPage where the full setup (engine, triggers, whatever related) is described
1.1.94 - solved: use non-PS2 if wheelspeed is needed
- went from 1.1.88 to 1.1.94 as recommended and using vemstune 16/6/2011.
- Speed sensor feature is completely missing from my saved config and i am not allowed to see it from base menu.
- Likely you selected PS2 firmware that does not have wheelspeed sensing (the PS2 clock uses up the 1st wheelspeed input).
- Other users do not have this problem.
- yes, just Choose non-PS2 firmware
- actually, Sami reported that his noisy (mechanical reed-relay type audi transmission) wheelspeed sensor reading is not stable with 1.1.94 when input prells at 450 km/h period (he provided suitable triggerlog to see this) and in 1.1.95 we implemented a more advanced wheelspeed filtering that fixed that sick case: you can use 1.1.95 non-PS2 also.
THANKS> im going to go with 1.1.95 now. I thought i was supposed to use PS2 and not non-PS2(dont understand the difference). I would also appreciate if you could point out where to look for knock sensor settings for audi, as well as speed sensor settings for audi 5cyl engine. Thanks, Vasilis
Firmware:
- v3.1 #56 & #57, 1.1.70 I have a problem with new firmware on 3.1 board. It only works in limphome mode.
- using latest Vemstune (2010-03-08 and 2010-02-05). The problem is that after startup spark angle stays fixed on 10° all the time
- similar situation with stepper IAC valve. When I turn on the engine it goes in max closed position and stays there
- 3.1 boards are still supported. It's a bootloader problem. Was the bootloader upgraded (or atmega changed) on these boards ? This "limphome" protection was implemented by Andrey, ment for a batch of pirate boards (most in Bulgaria and Russia). If your board is "genuine" (even if old), contact through WebShop (so you can receive a new bootloader, or other solution). Write the original Order-ID or other details (date of purchase)
1.1.88 knock_chan setting of 168 resulted in an increase in spark advance. vemslog and additional data here: http://www.vems.hu/wiki/index.php?page=MembersPage%2FMarcSwanson%2FFirmwareBugs
1.1.81 anytrim for boost do not work as expected. Boost target is boost dependant. Here is deeper description + real life and bench test .vemslog http://www.vemssupport.com/forum/index.php/topic,1490.0.html GintsK
Thanks for the Error report, problem found and fixed in Fw 1.1.86