In case of bug reports please do not forget to write VemsTune version and V3 version
!V3 related
- VemsTune 4-24 and 5-18 versions. V3 fw 1.52.2. Laptop PC using Windows XP, serial port.
- Program "flashes" every 3-4 seconds. Sometimes will not allow me to type in numbers for a setting(inj. deadtime, 4 digits) without "flashing" and setting goes back to old number.
- Program freezes up on occasion, I will try to document the specific instances.(KevinBlack)
!Round related
- From version 4-24, VemsTune will not re-start after setting the device to "round"(KevinBlack)
- Will be fixed in next release: quick solution: open config\v3gui.cfg find defaultDevice and set back to v3
VemsTune Suggestions, some are already implimented:
Simple Keystrokes. Autronic is by far easiest.
- Hot keys will be configurable by user so everybody can set his favorite.
- "Escape" opens one of the drop-down menus (ALT in Vemstune-good)
- Then "Left/Right Arrows" to move to different setions - DONE
- "Hold Shift/Move Arrows" to copy cells in Tables - DONE
- Suggest using "+ -" for increase/decrease, and hold "CTRL" for larger change. Seems easier than "Q W E R" keys.
- Use "Page Up/Page Down" keys to move from one sub-menu item to another. Example: VE Table - Page Down to IGN Table - Page Down to Lambda Table.
- "Review Mode" like in Megatune, makes it easy to check/adjust all of the settings efficiently.
- vertical/horizontal arrow strokes act differently when used in 3D-map only (just like in Megatune) or widget 3D view with gauges (vertical/horizontal change places in 3D window)
- alt+arrow to correct 3d map viewing angle to correct this, defaults should probably be fixed /Emil
- If am I right, your problem is when you open a 3D table in menu and from group stored angle of 3D is different?
- that really was the case. Another pity is that 3D table can't be rotated as much as in MT. Booost map for example is much easier to tune upside down.
- If a 3D table belongs to a group then angle comes from the group descriptor.
- If a 3D table not belongs to a group then angle comes from the cfg file.
- Rotation will be extended!
Enhanced ergonomics:
- When not in single gauge-group mode and gauge group layout behaviour is "attach within mainframe" I suggest that you can save a number of tabs as "home pages" when you open up the progam and open a project or connect to a ecu. And that you can switch between tabs with ALT-TAB(forward) and ALT-TAB-SHIFT(backwards) , this will allow users to jump quickly between various tabs to tune and various gauge-groups they like to have open. They can then change each group to suit them and their tuning needs. This should make switching between tuning various tables quick and you don´t need to close each one to open up another one. Very similar to how Internet Explorer and Firefox operate now. - Gunni
- a combined function of 'convert to csv' + 'view last log' would be fine (or other method to directly write log for megalogviewer)
- support for spaces in path (default vemstune location!) or filename necessary -couldn't use 'view lastlog with MLV' correctly until the log folder 'Program Files' contained spaces
- actually using user selectable log&cfg folder would be fine
- file dialogs behavior: saves last used folder
- different keyboard shortcuts for every (often used) function
- ability to export and import tables separately from the table windows (like in megatune)
- terminal program integrated into vemstune would be fine
General:
- MSQ export of VE and Lamba has table size inverted. (14x16 instead of 16x14) Is this hardcoded or in a config?
- Thx. Fixed! next release will contain the right rows and cols.
- Width and Height fixed, but data doesn't line up
- Ability to copy / paste entire or portions of any table
- Just Drag and Drop a *.vemscfg on a given table. Only the appropriate table and x,y axis bins will be loaded into table editor.
- A SAVE Project button so that offline project adjustments can be made for customers and then emailed to them.
- Incorporate a tool to "fix the ecu" when stuck in Boot loader mode. PSITuner is good for this.
- VemsTune can detect Boot loader mode.
- If the ECU enters in boot mode at powerup fw is damaged so you have to upload firmwarwe to fix it.
- If the ECU enters in boot mode (by manually or with some tool) just powerdown and powerup the ECU
- If the ECU somehow runs the damaged fw you can use a serial looback at powerup and the ECU will enter in boot mode
- VemsTune can detect Boot loader mode.
- The follow function is not implemented into the 3D table view yet! The cursor should stay in the latest position when the follow(for example SPACE) button is pressed-FERO
- The cursors are exchanged in the 3D table view. The engine's actual position should be the green plot, and the actally tuned position should be the red cross, like in megatune was. Now they are changed in vemstune.Now it's hard to see where is the engine now, the red cross is hard to follow with eyes! Very-very confusing!!!-Fero
- Ok we will change this or make it configurable.
Can you give a more detailed info of the scenario
- Tool for Generate Trigger (does this work? Could use for testing outputs)
- Some way to either split screen with MegaLogViewer, or a simple key to "Toggle" between VemsTune and Megalogviewer.(KevinBlack)
- these are 2 independent application so you can use ALT-TAB
Connection bug: The connection lost randomly in about 1-5 minutes, and the gauges starts "jumping".I'm using 1.1.54 non-PS2 firmware, with VEMSTUNE_2009.05.27, with windows XP eng, and the USB-RS232 adapter from webshop, with acer aspire dualcore laptop. -Fero
- Can you demonstrate this behaviour. Unfortunately we unable to reproduce. Tried with CPU 100% load, didn't noticed connection lost.
VemsTune log
When playing a log in VT it would be nice if we could move the slider left right fore quick playback of an episode in the log.
- Problem: logging is stopped when ecu is disconnected (ignition off) and when its on again, logging restarted but previous information dissapear from log. Very annoying when the motor stalls and the reason couldn't be seen in logs
- VemsTune creates new log when ecu is connected. So when you start a log and the ECU after a while ECU is disconected and connected again then you have 2 logs.
short key bug
When opening Ign table the short key “W” due not seams to work.
- “W”?? You mean: SHIFT-1, SHIFT-2?
- When tuning ignition table the “W” key due not reduce the value of the row/field its ok in 3D tuning
- I have the same problem(0.9.85)
- Could it be possible to add a background to the gauges?
- Currently not. Need some implement.
- I think of a simple object like jpg/bmp image? (example Kevlar background)
- And maybe to could lock them to prevent sensitive keypads so they are not moving around.
- Check this Lock Gauge problem.
- Also saved and save as could be nice.
- I thought save config and save config as
- Gauges can be moved, makes it smaller, larger and saved.
- If we type in the firing order could the value of injector and ignition table be automatic generated if using standard inj A = cyl 1. inj B = cyl 2 same with ign. nice job -Peter
- I tried to configure 3D editing keys same as MT was. It work until two-three last releases (now 0.10.0 (2009.10.02)). Now Ctrl+Shift+up/down changes 3D window height instead increase/decrease in big steps. -GintsK
SD card readout
"SD card overview extended" is only supported in latest (1.1.53 or 54?) firmware that makes entry for each startup (as if data were in different files, still can be read as a sequence of blocks though).
- SD card older readout functions worked in vemstune, but "SD card overview extended" worked sometimes, sometimes crashed (on a certain car it crashed repeatedly). It's a very nice feature, the data in the giant 1Gbyte card is hard to use other ways.
- if the fw is old, or better, the readout data does not seem like (per-inode entries), than it should warn "Erase SDcard and start logging with 1.1.54 firmware or newer to use this one-file-per-startup feature" or similar text.
- Good idea!
- if the fw is old, or better, the readout data does not seem like (per-inode entries), than it should warn "Erase SDcard and start logging with 1.1.54 firmware or newer to use this one-file-per-startup feature" or similar text.
Would it be possible to show some interesting values about the log before downloading to pc. Like max rpm and max kpa. This way you know what logs to download to pc when racing. Transferring logs is slow. So it would be nice not to waste time transferring the wrong logs (driving to the pits, waterbox, etc). - brieken
Upload stuff without using any menu-s
An installer says: "When a customer has problems I like to be able to send finished mtt files to him, these can then be sent with command line tools or if he has communication problems I help him with bray over the phone"
Finished files make a lot of sense. It was planned that one would send project file, where the RIGHT firmware and/or config can be uploaded with 1..2 clicks (not lost in menu-s).
Vemstune (or an equivalent .exe or .pif or .bat tool in the same dir) must be verified to work with .vemscfg or .vemsproject file as command line argument. Drag'n'drop file onto running vemstune or it's icon should preferrably do the same.
- .vemscfg Upload / cancel dialog (serial port preferences must be possible to change)
- .vemsproject : dialog/wizard with direct (not through menu) 1 click access to verify firmware, upload firmware, verify config, upload config
- Offline save *.vemscfg, and Drag&Drop *.vemscfg onto vemstune will solve this process
Note that the vemstune over the network will be very useful in many cases, but dealers still need a way to prepare project / vemscfg files (in a documented way!) that can be uploaded extremely quickly (without using menu-s) by a computer-illiterate child supported over the phone.
- Remote tune over TCP connection feature is in integration/testing phase, planned to work only in newest firmware only with SIPR protocol.
Offline config editing
- Is it possible to save config after editing offline. I can't find anything that will let me.
- You mean you can view just not change and save ?
- I can change everything once I have loaded the config, but I can't find anyway to save the config
- Offline save to vemscfg functionality planned in next release.
- You mean you can view just not change and save ?
-- How can you save a config if there isn´t a way to make new ones? And when have maded changed to maps and hit save config.
The program just says "There is no data to save" and nothing get´s saved. So offline tuning and changing still doesn´t work
- Gunni
- You must download and install the appropriate firmware. VemsTune needs the given firmware config descriptor(global.h) to save. We will change this error message (it is misleading).
- At the moment there is no way of just loading a project and start editing the "empty" config and then saving it to a file. It should at least have a Save as.. function so you can actually select to wich file to save the config. I´m talking about setting up a .vemscfg just like you can a .msq from scratch without connecting to a ecu at all. I don´t have a vemscfg cause I can´t save one from scratch and I don´t have a ecu to "download" one. - Gunni -
- offline config bug: kpa scale values are halved in ignition and ve tables when a vemscfg loaded offline (guess it's related to high-boost?)
Gauges
- How can I add new gauges (especially knock_cyl_0_knock_val) to VemsTune and how Can I log it? I have tried to put vemsv3.ini, vemstune-v3-1.1.27.ini, GaugeSymbols.xml but no success.
- RT data can be displayed only if there is at least one descriptor associated to it.
- The gauge descriptor stored in db file. Create new gauge descriptor functionality planned in next release.
- __Can I log it?__ I think you mean how can I convert it to csv (*.vemslog contains all raw data).
- To convert it to CSV you have to edit manually the appropriate *.ini (for example: vemstune-v3-1.1.27.ini) and go to __[Datalog]__ section and add new __entry__ to it.
Firmware Version
- I am currently running firmware 1.0.79, but VemsTune does not seem to suport it?!?! I am also led to believe VemsTune also suports 1.0.78. FirmwareChanges also states to use VemsTune with 1.0.78. None of these firmware releases are available in the web download tool. there is 1.0.75, 1.0.76 and 1.0.80 releases, but I cannot find ANY infomation regarding these on this Wiki!?!?!?! I refuse to use any of the 1.1.XX firmware versions as i suffered a loss of 14 degrees of 'trigger tooth before TDC' and serious kickback when cranking the engine to the point it was killing the battery.
- Can not find the new function (wheelspeed, wheelspeed-based launch and the new knock-threshold-map) in 1.1.61 non ps2 in VemsTune when i make a new empty project.
- I found a new row in the defaultfirmwareconfig directory in the new 0.10.0 VemsTune called CompileOptions: 0000001B, and loaded into VemsTune, the program showed the Mics Output new settings. I played it with a bit, but not got any logics. With ff it shows the alternate knock settings to. How this varible work???
How do I get 1.0.79 to work with the current version VemsTune?
There is a big problem with vemstune 2009.06.25 version. I tried several firmwre versions. All of them has the problem. The vemstune has got an error message:The specified database file ( D:\VemsTune\config\hotkeys\profiles.db ) is not exists! . And the keyboard keys not working for 3D tables, or gauges. I even can't move the cursor in 3D tables. -FEro
With 2009.06.25 version can't make map bin above 255 in VE,IGN,Lambda table editor - offline test with 1.1.27 and 1.1.56 vemscfg - more than one report in uk forum too:
http://195.159.109.134/vemsuk/forum/index.php/topic,931.0.html
Still having problems with this even with the latest version of vemstune. When on base setup, bins for kpa are changed to 4>510,it still reads highest kpa on the tables as 255.
is there a solution?
Vasilis P.