Runout
Some factors can impact VR trigger quality.
The amplitude of tooth pulses is not equal
This is a common error with homemade trigger wheels that have a long deep gap at the missing tooth (this results in a higher amplitude around the missing tooth). Professional wheels have a continuous depth-change at the missing tooth, full depth is only reached at the middle. Examine a 60-2 Bosch wheel.
triggerwheel is not centered on the shaft
Sine wave will modulate the VR signal amplitude, so the arming threshold becomes important, especially at high RPM.
If in doubt, record VR signal with scope or your notebook soundcard.
Variation in individual tooth-height just makes the problem worse. Mik was the first to experience such problem when he patched his original (quite exotic) 18-1 + 18-1 crankwheel with a surgery for normal 36-1 tooth. The added tooth had smaller amplitude than the original teeth.
Soundcard can be used to record VR signal
WhatEverYouDoYouDoItAtYourOwnRisk !!! (take care of your soundcard)
- voltage divider with 10..22k and 1k resistors
- series cap > 100nF (220nF is perfect. Most soundcards have internal cap, but it doesn't hurt to have one just to be safe)
Since the VR signal amplitude can be quite high (especially at high-RPM, often >30V), the line-in input should be preferred to the mic-input. With mic-level input a much higher divider can be used, eg. 100k and 1k.
- Some playing with the mixer is always needed to get a wav with desired amplitude
- at idle the signal must stay below 10% amplitude so it stays within limits at high-RPM.
LM1815 arms at about 0.8 * peak
Note that the 20% safety margin in the VR chip isn't shown. The margin should eliminate any runout problems on a multitooth triggerwheel, but if the teeth for some reason result in a 20% amplitude difference there will be trigger problems.
This is a simulation of a four tooth triggerwheel at 3k (V8). The trigger occur when the VR signal fall down past 0v. The trigger is armed for the next trigg after going higher then the blue trace.
60 tooth at 3000rpm
The same triggerwheel, with the same runout at 6000rpm. As you can see the margin between the ARM threshold and the VR signal has decreased.
Notes
- the pictures do not show modulation correctly, they are using addition instead of multiplication in function VR(t) = sin(t / t0) * (1 + 0.2 * sin(t/(36*t0))). Since only the peak is important, and the negative peak is not, this changes nothing
- I couldn't easily simulate the missing teeth but that doesn't change anything
- LM1815 datasheet says typical arming treshold is 80% of peak value, but worst case is 90%. (deviance to the other direction, 40% does not cause problem). Should we measure this characteristics of each LM1815 during board testing ?
If someone want to waste some time on simulating this better:
http://www.vems.hu/files/JorgenKarlsson/triggersim.zip
Proposed solution
- appr. 150k resistor in series with C38(=220nF). This is an onboard modification for v3.0 .. v3.2. 220k sounds a bit high, but it would work. Please do this mod for v3.0 .. v3.2 boards you assemble to full units for your customers with unknown wheels. Easy to do cleanly with 3 steps (unsolder C38, tiny tracecut, scratch off some solderprotect, solder C38 and series 0805 resistor from rescukit).
- A similar solution is the standard factory-populated setup since v3.3
- Could someone explain this mod in a little more detail? I have found the capaciter on my board, it is in parallel with a resister. 1 side goes to pin 7 on the LM1815 and the other side goes off into the wild blue yonder. After I desolder C38, which side does the resister go? MY board is V3.2 sn 110. As a side note, I get no errors counted on the lcd when vehicle is running and sometimes 1, maybe 2 errors if any during cranking, am I looking in the wrong place? Every now and then something drops out and I loose fuel pump, spark, and injection for a split second. The board is still getting power when I check it with a scope, and I get no resets. I have tried hooking the vr sensor up backwards but the car wont even start.
- A similar solution is the standard factory-populated setup since v3.3
- or jumper LM1815 for non-adaptive mode (eg. pin5 to +5V for max arming threshold).
See also