VEMS Home Products Documentation Wiki Webstore
WikiHome ProjectPage DocsPage UnderDevelopment MembersPage SiteIndex RecentChanges Preferences
History of VemsTune/QuickStartAudi
Older Newer
2014-12-15 11:41:28 . . . . catv-80-98-222-153.catv.broadband.hu [note: save and archive the vemscfg before working on it; The procedure should no]
2012-11-18 23:23:26 . . . . catv-80-98-222-153.catv.broadband.hu [logiclevel ignout instead of stepper (simple cure for only cyl3 sparking)]
2012-07-03 09:40:18 . . . . adsl183-125.pool.businesstel.hu [minor comments about options]
2011-08-21 12:20:14 . . . . 53d82fd0.adsl.enternet.hu [minor spelling]
2011-04-28 11:41:18 . . . . 3e44a184.adsl.enternet.hu [Audi Quick start has been simplified]
2011-04-28 11:39:25 . . . . 3e44a184.adsl.enternet.hu [ Audi Quick start has been simplified]
2010-11-28 13:12:04 . . . . 87.226.1.232 [Idle PID D experience]
2010-11-28 12:31:28 . . . . 4d6f4e82.adsl.enternet.hu [audi IAC pid D term should be higher ? Around 100 instead of 33 ?]
2010-08-11 08:50:17 . . . . 3e44a346.adsl.enternet.hu [remove old(not working) functions]
2010-06-03 14:12:55 . . . . 3e44bc28.adsl.enternet.hu [clarify the steps with newer vemstune]
2010-05-13 17:10:04 . . . . 4d6f4652.adsl.enternet.hu [File / Project / Open + Config upload in new vemstune]
2010-05-13 17:06:20 . . . . 4d6f4652.adsl.enternet.hu [newer: File / Project / open + config upload]
2010-01-22 18:20:41 . . . . MembersPage/MarcellGal [note about 1.1.65 defaultfirmwareconfig trick]
2009-06-21 22:34:35 . . . . 3e44b057.adsl.enternet.hu [quick project install instructions were hidden in an old vemstune page version]

Changes by last author:

Changed:
Since VemsTune 2011-04-22 Audi Quick start has been simplified.

old method can be found: http://www.vems.hu/wiki/index.php?page=VemsTune%2FQuickStartAudi&version=8

Audi AAN and 3B boxes are sent out with base map with applied changes as requested in the order comment.

* most common change: requested with "630cc / 670cc / 727cc injectors" (same injector, just flowrate at 3bar / 3.5bar / 4 bar according to square-root formula)... req_fuel=3.0 msec (instead of ~7.5msec for the small factory injectors)

* boxes sent out after 2008-07-31 "Cam HALL Inverter" is standard

Changed:
It can be reach from: Tools/Firmware/Audi config upload (instead of File/project)
Before working on a device, ALWAYS save, and ARCHIVE the config .vemscfg file to a safe place.

----

NOT NEEDED ANY LONGER, just left for reference

Even older method [here].

Simplified "Audi Quick start" method below was available since VemsTune 2011-04-22. It was primarily used when the factory config was not saved, than messed up (for 3B and AAN engines with certain injectors, with or without cam-HALL inverter and certain ignition output setups).

VemsTune menu was moved to: Tools/Firmware/Audi config upload (previously under File/project)

Added:
* Ignition outputs of the Audi AAN (ABY, ADU) controller intentionally changed on devices manufactured (or "retest-repaired") after 2012-07-12 (the new "logiclevel i259" outputs are somewhat more tolerant than the stepper).

** The paper (included with these new units) say: "Ignition driven by logic level."

** The configuration in the ECU is updated to match, but in case old config is loaded back by the user in any way (especially if experiencing "only cyl3 sparking" symptom), verify the ignition outputs (in firing order from top to bottom):

***Cyl1 Ign ch0 (old standard was Stepper D)

***Cyl2 Ign ch1 (old standard was Stepper C)

***Cyl4 Ign ch6 (old standard was Stepper B)

***Cyl5 Ign ch5 (old standard was Stepper A)

***Cyl3 Ign ch4 (same in old and new standard)