Changes by last author:
Changed:
|
----
# As per [manual], * set the constants, * Get the engine started and idling, * Then set the PWM criteria, * Then set the cold start and warm-up enrichments, * Then set the VE table, * Set the acceleration enrichments, ---- |
| Currently, in order to make testing simple, I have the config setup for 6 tooth, coil type ignition. Using just a test harness at the moment with the trigger coming from my pc set to trigger at 250rpm. Once the fuel pump relay stops cutting out, I will set up the ignition and injector channels properly. |
| Config.txt 1.0.23 |
| Config.txt 1.0.38 |
| primep=64 |
| primep=32 |
| cranking_thres=0A I was playing with it from 100 to 1000 rpm |
| cranking_thres=02 |
| awc=FF |
| awec=FF |
|
warmup_clt[5]=8C
warmup_clt[6]=84 warmup_clt[7]=78 warmup_clt[8]=6F |
|
warmup_clt[5]=96
warmup_clt[6]=8C warmup_clt[7]=87 warmup_clt[8]=6E |
| req_fuel=46 |
| req_fuel=6E |
|
tps_thresh=04
tpsasync=05 |
|
als_cut_mintps=04
tpsasync=01 |
|
tpsdq=64
decel_fuelcut_thres=3C overrun_fuelcut=28 overrun_fuelresume=28 |
|
launch_enrich=64
launch_retard=00 overrun_fuelcut=14 overrun_fuelresume=11 |
| baro=66 |
| als_max_cut=60 |
| iac_conf=72 |
| iac_conf=52 |
| iac_warm_rpm=46 |
| iac_warm_rpm=06 |
| iac_afterstart_steps=0A |
| iac_speed=0A |
| iac_integral_speed=36 |
| launch_rpm=36 |
| iac_pid_conf=00 |
| als_cut_maxtps=00 |
|
iac_ign_advance_change=04
iac_ign_retard_change=04 |
|
iac_ign_slope=04
softrpm_range=04 |
| mt_unused=00 |
| als_enrich=00 |
| wbo2_warmup_target=FF |
| als_react_tps=FF |
| ve_learn_conf=01 |
| ve_learn_conf=00 |
|
lcd_offs[0]=FF
lcd_offs[1]=FF lcd_offs[2]=FF lcd_offs[3]=FF |
|
kpa_conf=21
ign_balance=00 als_retard_mintps=FF als_retard_maxtps=FF |
| primary_trigger=0E |
| primary_trigger=CC |
|
tooth_wheel=06
trigger_tooth=01 |
|
tooth_wheel=0B
trigger_tooth=00 |
|
crank_minper=FA
tooth_wheel_twidth1=14 tooth_wheel_twidth2=14 |
|
crank_minper=7D
tooth_wheel_twidth1=0A tooth_wheel_twidth2=00 |
| engine_off_delay=00 |
| engine_off_delay=08 |
| fuelpump_channel=40 |
| fuelpump_channel=70 |
|
als_lowrpm=00
als_maxtps=00 als_ignretard=00 als_rich=00 |
|
als_deact_rpm=00
als_deact_time=00 als_deact_egt=00 als_retard=00 |
| egt1_offs=FF |
| als_tks_channel=FF |
| water_pump_hyst=00 |
| water_pump_hyst=0F |
|
toothrel_normal=B5
toothrel_missing=76 fuelcut_min_kpa=00 |
|
toothrel_normal=79
toothrel_missing=00 fuelcut_min_kpa=0E |
| softrpm_rpm=37 |
| Tables.txt NOT properly tuned yet, still have trigger dropout issue. |
| Tables.txt NOT properly tuned yet. |
|
j[0]=3F80 4980 4D80 4E80 4F80 4F80 4F80 4F80 5080 5680 5C80 6380
j[1]=4180 4980 5080 5680 5980 5A80 5A80 5C80 6580 6D80 6D80 6C80 j[2]=4580 4D80 5080 5A80 5880 5980 5C80 6380 7180 7C80 7D80 7580 j[3]=5180 6980 7780 7E80 8480 9280 9F80 AA80 AE80 AB80 A580 9F80 j[4]=5A80 7C80 8780 8C80 8E80 9B80 A680 B180 C180 BE80 B980 B180 j[5]=6080 8680 8C80 9680 9980 A980 B680 BD80 C480 C680 C080 BA80 j[6]=6080 8680 8C80 9680 9980 A980 B680 BD80 C480 C680 C080 BA80 j[7]=6080 8680 8C80 9680 9980 A980 B680 BD80 C480 C680 C080 BA80 j[8]=6080 8680 8C80 9680 9980 A980 B680 BD80 C480 C680 C080 BA80 j[9]=6080 8680 8C80 9680 9980 A980 B680 BD80 C480 C680 C080 BA80 j[A]=6080 8680 8C80 9680 9980 A980 B680 BD80 C480 C680 C080 BA80 j[B]=6080 8680 8C80 9680 9980 A980 B680 BD80 C480 C680 C080 BA80 l[0]=3F 37 37 37 37 37 37 37 37 37 37 37 l[1]=39 36 36 36 36 36 36 36 36 36 36 36 l[2]=3B 3B 3B 3B 3B 3B 3B 3B 3B 3B 3B 3B l[3]=47 47 47 47 47 47 47 47 47 47 47 47 l[4]=4D 4D 4D 4D 4F 4F 4F 4F 4F 4F 4F 4F l[5]=55 55 55 55 5A 5A 5A 5A 5A 5A 5A 5A l[6]=66 66 66 66 66 66 66 66 66 66 66 66 l[7]=6B 6B 6B 6B 6B 6B 6B 6B 6B 6B 6B 6B l[8]=6B 6B 6B 6B 6B 6B 6B 6B 6B 6B 6B 6B l[9]=6B 6B 6B 6B 6B 6B 6B 6B 6B 6B 6B 6B l[A]=6B 6B 6B 6B 6B 6B 6B 6B 6B 6B 6B 6B l[B]=6B 6B 6B 6B 6B 6B 6B 6B 6B 6B 6B 6B n[0]=26 32 37 39 3F 41 45 47 50 4E 4C 4A n[1]=28 31 3B 3F 44 48 4E 4E 56 54 50 4E n[2]=2A 3E 44 47 4C 51 55 5C 5A 56 54 50 n[3]=2C 42 49 53 5B 5F 64 62 5E 5C 58 56 n[4]=2E 44 52 5C 66 6A 68 66 62 5E 5C 58 n[5]=30 48 56 62 6C 70 6E 6A 68 64 60 5E n[6]=32 4A 5A 64 6E 72 72 6E 6A 66 64 60 n[7]=32 4C 5C 68 72 76 74 70 6E 6A 66 62 n[8]=36 50 60 6C 78 7C 7A 76 72 6E 6C 68 n[9]=36 52 62 70 79 7D 7D 7A 76 72 6E 6A n[A]=38 56 68 74 7A 7D 7F 7D 7C 78 74 70 n[B]=3A 58 6A 78 7C 7E 80 7E 7E 7A 76 72 k[0]=14 1E 32 46 5A 66 78 8C A0 B4 C8 FA |
|
j[0]=4180 5280 5D80 6780 6C80 6F80 6F80 6C80 6980 6480 6280 5F80
j[1]=4480 5280 6480 6C80 7480 7680 7680 7480 6F80 6C80 6980 6480 j[2]=4580 5180 6780 7180 7980 7B80 7B80 7680 7480 6F80 6C80 6980 j[3]=4A80 5880 6C80 7680 8180 8380 8380 7E80 7B80 7680 7480 6F80 j[4]=4E80 5F80 7080 7B80 8380 8880 8680 8380 7E80 7980 7680 7180 j[5]=5080 6680 7680 8380 8B80 9080 8D80 8B80 8680 8180 7B80 7980 j[6]=5280 6980 7980 8680 9080 9380 9380 8D80 8880 8680 8180 7B80 j[7]=5580 6C80 7E80 8880 9380 9880 9580 9380 8D80 8880 8380 7E80 j[8]=5780 7480 8380 9080 9A80 9F80 9D80 9880 9380 9080 8B80 8680 j[9]=5A80 7680 8680 9380 9F80 A280 A280 9D80 9880 9380 8D80 8880 j[A]=5F80 7B80 8D80 9A80 A580 AA80 AA80 A580 9F80 9A80 9580 9080 j[B]=6280 7E80 9080 9F80 AA80 AF80 AC80 A780 A280 9D80 9880 9380 l[0]=3D 39 37 37 37 37 37 37 37 37 37 37 l[1]=3D 39 37 37 37 37 37 37 37 37 37 37 l[2]=3D 3D 37 37 37 37 37 37 37 37 37 37 l[3]=37 37 37 37 37 37 37 37 37 37 37 37 l[4]=37 37 37 37 37 37 37 37 37 37 37 37 l[5]=37 37 37 37 37 37 37 37 37 37 37 37 l[6]=37 37 37 37 37 37 37 37 37 37 37 37 l[7]=37 37 37 37 37 37 37 37 37 37 37 37 l[8]=37 37 37 37 37 37 37 37 37 37 37 37 l[9]=37 37 37 37 37 37 37 37 37 37 37 37 l[A]=37 37 37 37 37 37 37 37 37 37 37 37 l[B]=37 37 37 37 37 37 37 37 37 37 37 37 n[0]=30 40 48 50 54 56 56 54 52 4E 4C 4A n[1]=34 44 4E 54 5A 5C 5C 5A 56 54 52 4E n[2]=36 46 50 58 5E 60 60 5C 5A 56 54 52 n[3]=3A 4A 54 5C 64 66 66 62 60 5C 5A 56 n[4]=3A 4C 58 60 66 6A 68 66 62 5E 5C 58 n[5]=3E 50 5C 66 6C 70 6E 6C 68 64 60 5E n[6]=40 52 5E 68 70 72 72 6E 6A 68 64 60 n[7]=42 54 62 6A 72 76 74 72 6E 6A 66 62 n[8]=44 5A 66 70 78 7C 7A 76 72 70 6C 68 n[9]=46 5C 68 72 7C 7E 7E 7A 76 72 6E 6A n[A]=4A 60 6E 78 7D 81 81 7D 7C 78 74 70 n[B]=4C 62 70 7C 81 85 83 7F 7E 7A 76 72 k[0]=14 1E 28 32 3C 46 50 5A 64 6E 78 82 |
|
h[0]=05 0A 05 0A 05 0A 05 0A
h[1]=00 00 00 00 00 00 00 00 |
|
h[0]=01 02 04 08 20 40 80 10
h[1]=00 00 00 00 00 00 00 03 |
|
b[0]=28 30 38 40 48 50 58 60 FF FF FF FF
t[0]=20 40 17 80 A0 C0 E0 FF |
|
b[0]=30 38 40 48 50 58 60 FF FF FF FF 20
t[0]=40 17 80 A0 C0 E0 FF FF |
|
I remember an email where someone got frustrated and loaded a blank config to start from but didnt save it. Can someone instruct me how to do that?
*I should have specified, I know how to make mtt and upload the mtt file through the terminal program. **I was hoping to figure out how to start with a completely blank config (like when megatune fried it)and just start from scratch. Putting in enough variables to get it triggering and the fuel pump relay live and then see what variable is killing me (if any). I am at the end of my rope, I cant think of anything else to try. It was someone doing a 4.5l lexus swap, from seattle I think. A: You h[0] (injector outputs table in megatune) is not correct, at least not in combination with the fuelpump_channel = 40 , which is injector table output number 5 (starts from 0) You are actually trying to use 2 injector outputs (A+C) for fuelpump. I would recommend h[0] = 05 0A 05 0A 10 20 40 80 which in injector outputs table in megatune would be 5, 10, 5, 10,16,32,64,128 then fuelpump would use injector output E. // Emil Larsson |