_____ | _ | | | | | | | | | \ \/' / \_/\_\
##### ## ## ## ## ## # ####
## ## ###### ###### ## ## ## ##
##### ## ## ## ## ##### ## ##
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: '''Subpage of VemsTune''' Example to upload project files that have been prepared (usually by the install supervisor or power-users) * for certain (family of) setups. "Family" means: usually the trigger, IAC and other parameters are the same. ** There might be choosable options, like for injector size, cam-HALL example yes/no, or for ignition output setup (AAN/3B). ---- '''Notes''' The examples below were captured with VemsTune 2008-10-16 release. In '''2010 vemstune these functions are available under File / Project'''. Namely * '''File/Project/Open''' (1.1.27 12x12) * '''File/Project/Firmware upload''' ** '''optional.''' The project config upload can be used with newer firmware, but than review needed to verify the auto-filled tables. * '''File/Project/Config upload''' ** than select the appropriate options Experienced installers can prepare different settings for other engine family, with similar options like below. Even if the software part of upload can be solved with a few clicks, the important safety measures still apply. Do not skip these (you might fill cylinders with fuel, blow ignition fuse, or worse...). Before firmware upgrade, always: * '''remove ignition fuses''' * '''remove fuelpump relay''' ** or otherwise make sure the fuelpump is off, eg. hidden anti-theft switch * '''remove injector connectors''' * upgrade firmware, upload and verify config and tables. Reboot. Than measure voltage in the igncoil and injector connectors (switched pin not pulled to ground, that is no 12V measured between the 2 pins). * Only if all is well, think about powering the fuelpump and inserting ignfuses ---- '''Project open + project config upload''' * '''File / Project / Open / 1.1.27 (12x12)''' * '''File / Project / Config Upload''' * the appropriate config files can be selected. http://www.vems.hu/download/v3gui/images/quick-config-upload.JPG The same procedure applies to 1.1.65 (or newer). If you '''upload an older config (1.1.27 in the examples) with recent VemsTune''' (2009-12 or later), it will automatically '''use "defaultfirmwareconfig/..." for any variable not found in the uploaded config'''. This "upgrade-feature" saves time: helps to get reasonable values in new tables (without extra steps). Note: it is recommended to review the tables and dialogs anyway. ---- '''IAC PID setting''' Someone suggests on MembersPage/RanzAudi that '''"IAC pid D-term" appr 100''' gives MUCH better behavior with the audi IAC PWM valve (and engine). The default setting (uploaded during the above steps) is IAC pid D < 35 so give it a try: bump it up as a test. Also give some feedback (here is OK). We'll make a much higher IAC pid D the default after some experimentation and feedback. I use high D values for Vems idle since 1.1.27 era. For some reason D is far less sensitive than P and I. My usual D values are in 80...200 range. But P and I varies in 8...25 range - aprox ten times lower. MembersPage/GintsK ---- '''Create individual project file''' - for advanced users The file is a simple XML format. # Rename/Copy the original .vemsprj file. # Open it with Your favorite XML editor. # The structure is very simple/straightforward. h Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.