_   _ 
 | | | |
 | |_| |
 |  _  |
 |_| |_|
        

###      
 ## ###  
 ## #    
 #####   
 ## ##   
 ##  ##  
#### ### 
         

  _____ 
 |_   _|
   | |  
   | |  
   |_|  
        

         
    ###  
   ##    
  #####  
   ##    
   ##    
   ##    
         

         
         
  #####  
 ##      
  ####   
     ##  
 #####   
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Subpage of VemsTune''' Example to upload project files that have been prepared (usually by the install supervisor or power-users) * for certain (family of) setups. "Family" means: usually the trigger, IAC and other parameters are the same. ** There might be choosable options, like for injector size, cam-HALL example yes/no, or for ignition output setup (AAN/3B). ---- '''Notes''' The examples below were captured with VemsTune 2008-10-16 release. In '''2010 vemstune these functions are available under File / Project''': namely File/Project/Open (1.1.27 12x12), File/Project/Firmware upload, File/Project/Config upload Experienced installers can prepare different settings for other engine family, with similar options like below. Even if the software part of upload can be solved with a few clicks, the important safety measures still apply. Do not skip these (you might fill cylinders with fuel, blow ignition fuse, or worse...). Before firmware upgrade, always: * '''remove ignition fuses''' * '''remove fuelpump relay''' ** or otherwise make sure the fuelpump is off, eg. hidden anti-theft switch * '''remove injector connectors''' * upgrade firmware, upload and verify config and tables. Reboot. Than measure voltage in the igncoil and injector connectors (switched pin not pulled to ground, that is no 12V measured between the 2 pins). * Only if all is well, think about powering the fuelpump and inserting ignfuses ---- '''Quick project install''' Install the latest vemsTune (at least version 2008.09.02) http://vems.hu/download/v3gui/ The installer will ask where to install the application (typical location C:/Program Files/VemsTune) # choose 1.1.27 ( vemsprojects/firmware_1.1.27/ ) even for 1.1.7x firmware as well (see "defaultfirmwareconfig" below) # Right click on audi-ann.vemsprj. A context menu will appear, 3 functions can be selected: http://www.vems.hu/download/v3gui/images/VemsTune-context-menu.jpg # Quick project upload (do both the firmware and config upload) # Quick firmware upload # Quick config upload '''Quick firmware upload''' Firmware upload dialog: appropriate Air and coolant files can be selected (2252 Ohm for sensors from webshop). Select the right one and Save it and Upload the firmware. http://www.vems.hu/download/v3gui/images/quick-firmware-upload.JPG ---- '''Project open + project config upload''' * '''File / Project / Open / 1.1.27 (12x12)''' * '''File / Project / Config Upload''' * the appropriate config files can be selected. http://www.vems.hu/download/v3gui/images/quick-config-upload.JPG The same procedure applies to 1.1.65 (or newer). If you '''upload an older config (1.1.27 in the examples) with recent VemsTune''' (2009-12 or later), it will automatically '''use "defaultfirmwareconfig/..." for any variable not found in the uploaded config'''. This "upgrade-feature" saves time: helps to get reasonable values in new tables (without extra steps). Note: it is recommended to review the tables and dialogs anyway. ---- '''Create individual project file''' - for advanced users The file is a simple XML format. # Rename/Copy the original .vemsprj file. # Open it with Your favorite XML editor. # The structure is very simple/straightforward.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.