__   __
 \ \ / /
  \ V / 
   | |  
   |_|  
        

___  ___
|  \/  |
| .  . |
| |\/| |
| |  | |
\_|  |_/
        
        

         
 ##      
 ##      
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
         

 _____ 
|  __ \
| |  \/
| | __ 
| |_\ \
 \____/
       
       

   ###   
  ## ##  
  ##     
 ####    
  ##     
  ##     
 ####    
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Firmware versions 1.1.xx The following cofigurations are for 12 crank (24cam) tooth primary trigger, single cam tooth secondary trigger. As found in Toyota, Honda, Mazda, and Nissan with CAS converter disk ( VehicleFitment/Nissan ) == 4 Cylinder == In '''config.txt''' * primary_trigger=07 # coil type, filtering, rising edge. * secondary_trigger=19 # camsync, rising edge. * tooth_wheel=18 # decimal 24 tooth (between cam pulses) * trigger_tooth=01 # or upto 05 * ign_tdcdelay=B4 # 90/0.5 = 180 (half degrees) * another_trigger_tooth=06 # 24 tooth/4 cylinders * tooth_wheel_twidth2=00 # No missing tooth * tooth_wheel_twidth1=78 # decimal 120 (30deg / 0.25) * rpmk[0]=0b * rpmk[1]=b8 #RPM constant for 4 cyl = 3000 (=0x0bb8) * alternate=13 # injgroups 3..0 (fire all banks during cranking) * ignchmax=03 # ignition 3..0 * cam_sync_r_edge_phase=33 * cam_sync_f_edge_phase=46 * reset_engphase_after=40 # since 720/0.25 = 2880%256 = 64 In '''tables.txt''' h[1]=00 12 0C 06 00 12 0C 06 # another_trigger_tooth=06 h[2]=10 30 20 00 10 30 20 00 # Firing order: 1, 3, 4, 2 ----- == 6 Cylinder == In '''config.txt''' * primary_trigger=07 # coil type, filtering, rising edge. Alternatively 06 would be falling edge (could be suitable for HALL, but not for VR) * secondary_trigger=19 # camsync, rising edge; alternatively 1d is same, but with filtering * tooth_wheel=18 # decimal 24 tooth (between cam pulses) * trigger_tooth=01 # or upto 03 * ign_tdcdelay=C4 # 98 crankdegrees * another_trigger_tooth=04 # 24 tooth / 6 cylinders tooth_width is allowed to be higher than 64 degrees. The missing tooth width is the upper byte. (there is no missing tooth anyway). Use 0 if the tooth distance is less than 64 degrees. * tooth_wheel_twidth2=00 * tooth_wheel_twidth1=78 # decimal 120, that is 30 crankdeg per tooth * rpmk[0]=07 * rpmk[1]=d0 # RPM constant for 6 cyl = 2000 (=0x07d0) * alternate=15 # injgroups 5 .. 0 (fire all banks during cranking) * ignchmax=05 # ignition 5..0 * reset_engphase_after=40 # since camsync is used In '''tables.txt''' h[1]=00 14 10 0C 08 04 .. .. h[2]=10 60 50 40 30 20 .. .. ----- == 8 Cylinder == In '''config.txt''' * primary_trigger=07 # coil type, filtering, rising edge. * secondary_trigger=19 # camsync, rising edge. * tooth_wheel=18 # decimal 24 tooth (between cam pulses) * trigger_tooth=01 # or upto 05 * another_trigger_tooth=03 # 24 tooth/8 cylinders * tooth_wheel_twidth2=00 # No missing tooth * tooth_wheel_twidth1=78 # decimal 120 (30deg / 0.25) * cam_sync_r_edge_phase=33 * cam_sync_f_edge_phase=46 * rpmk[0]=03 * rpmk[1]=e8 #RPM constant for 4 cyl = 3000 (=0x03E8) * ign_tdcdelay=B4 # 90/0.5 = 180 (half degrees) * alternate=17 # injgroups 7...0 (fire all banks during cranking) * ignchmax=07 # ignition 7...0 * reset_engphase_after=40 In '''tables.txt''' h[1]=15 12 0F 0C 09 06 03 00 h[2]= <depends on firing order>
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.