___   
(  _`\ 
| ( (_)
| |___ 
| (_, )
(____/'
       
       

         
         
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
         

 ##      
 ##      
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
         

         
         
 ######  
    ##   
   ##    
  ##     
 ######  
         

         
         
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
    ##   
 ####    

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
The following resources have been obtained while installing VEMS on Toyota 4A-GE 16V & 20V engines. VehicleFitment/Toyota/Injectors VehicleFitment/Toyota/Triggers VehicleFitment/Toyota/Sensors VehicleFitment/Toyota/IdleAirController ----- After the previous work using pull-down resistors we moved onto the suggested 10k->12V pull-up resistors and the addition of a 220nF cap on top of C40. Still not good, the latest trigger log shows some strange missing tooth issues: http://vems.hu/www.vems.co.uk/VEMSTrigger/4AGETrigger3.txt Action to try next: # Try to match the OEM pull-up of 0.6V with smaller value resitors. # Try pull-down resistors as before, but with LM1815 pin5 jumpered to cause LM1815 to ignore any voltage below 200-450mV # Use a seperate ground feed direct to the LM1815 chip. ----- Toyota 24+4 Trace: http://vems.hu/www.vems.co.uk/VEMSTrigger/24+4.PNG Recorded with USB Instruments Stingray Testing on the bench with: Recorded trigger as a wav works okay, testing distributor driven by a motor works fine. Testing with the trigger in the car through the loom does not give an RPM reading. '''Config & Tables''' http://vems.hu/www.vems.co.uk/VEMSTrigger/config.txt http://vems.hu/www.vems.co.uk/VEMSTrigger/tables.txt '''Connection Details''' The Ne (24tooth) trigger is connected to Trig1, the G1 (4 tooth) trigger is connected to Trig2. The G- combined ground connects to the common grounds. Two 270Ohm resistors pull the signal down to ground. '''Trigger Logs''' Initial test: http://vems.hu/www.vems.co.uk/VEMSTrigger/24+4InCarTrig.txt Test with the Ne and G1 trigger inputs changed over Ge to primary trigger, Ne to secondary trigger - we were out of clues so we thought we'd try it... http://vems.hu/www.vems.co.uk/VEMSTrigger/24+4AfterSwapTrig.txt Changing back to the correct trigger connections but removing the pull-down resistors. http://vems.hu/www.vems.co.uk/VEMSTrigger/24+4FinalMiseryTrig.txt A log from the bench test http://vems.hu/www.vems.co.uk/VEMSTrigger/24+4BenchLog.txt The owner of the car has produced a spreadsheet to try and analyse the trigger logs: http://vems.hu/www.vems.co.uk/VEMSTrigger/24+4waveformsgraphed.xls Toyota 24+4 Distributor: http://i81.photobucket.com/albums/j209/JMR_AW11/Ign6.jpg '''#10''' is the injector signal - indicating 1 injection event every two ignition events. Will this work with a divider of 2 to ensure that we get a batch injection event every second ignition event?
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.