####   
 #    #  
 #    #  
 #    #  
  ####   
         

         
         
  #####  
 ##  ##  
 ##  ##  
  #####  
     ##  
     ##  

  ___  
 / _ \ 
/ /_\ \
|  _  |
| | | |
\_| |_/
       
       

         
         
 #####   
 ##  ##  
 ##  ##  
 #####   
 ##      
 ##      

         
  ####   
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
  ####   
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Mainboard: Revision: r016_jk Status: unlocked Aim: Moved v_out to a software pwm, chared pin with MOSI earlier. Maybe finished for PCB manufacture. Aligned support pins for the DisplayBoard Displayboard: Revision: r011_jk Status: unlocked Aim: Fixing insane autoroutes and aligned connectors on main and display board. Write the new revision number and your initials and change the status to locked before you start working on the file. When you mail the file to HQ again you change the status to unlocked. A slight variation of the v3 procedure. ---- '''Todo:''' * Add EGT amp to display board. This will not be used together with the main board. Only as dedicated EGT gauge. *Add support pins for display board on the main board. ---- Dropped: * Find room for EGT. (An EGT amp could be added to the display board to make a cheaper EGT meter) * I'm thinking of finding an 8-way lowside switch (pie, eg. ULN... unipolar stepper drivers) and a 6 way highside (should be somewhere), SMD of course. * 3 pieces of 74HC259 would also relief the atmega from driving 3 timeslots (of the 6: the 3*7 would remain on atmega), so overall brightness would increase - still too low for daylight HUD ---- and ''log:''' * Aligned connectors on Main and Displayboard. * Add VBatt voltage divider. * Move LM1815 to clear the MAP screws. Placed the ISP connector. Added series capacitor on the VR input, that should not affect the VR sensors but would transform a square wave signal to a signal that can be used with the LM1815 VR interface. Removed the LM1815 bypass. Changed the MAT and CLT inputs a bit. Removed the software controllable 'RPM signal from 12V' amp. Made new 7seg part in library, the drawings wasn't any good. I'll get one to take the measurements on. Verified the 3*7 LED (the green 3.0 mcd/10mA is beautiful!) http://www.elfa.se/elfa-bin/setpage.pl?http://www.elfa.se/elfa/produkter/se/2021838.htm to be common cathode as per spec (Jörgen). Minor rearranging of components on the display board, still autoroutes. ---- Jorgen says these LEDDisplay are better for HUD (separate elongated PCB with tons of these, maybe right): * http://www.elfa.se/elfa-bin/setpage.pl?http://www.elfa.se/elfa/produkter/se/2021825.htm * http://www.elfa.se/elfa-bin/setpage.pl?http://www.elfa.se/elfa/produkter/se/2021827.htm * http://www.elfa.se/elfa-bin/setpage.pl?http://www.elfa.se/elfa/produkter/se/2021827.htm
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.