##### ## ## ## ## ##### ## #####
## ## ## ## ## ## #### ##
### ## ### ## ## ## ## ## ## ## #### ###
## ###### ## ## ## ###
____ / ___| \___ \ ___) | |____/
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: '''Motronic-55 plug and play ECU''' - various pinouts for different engines There was demand for an advanced ECM that can be plugged to the place of a 55-pin (19 + 18 + 18) [http://catalog.tycoelectronics.com/TE/bin/TE.Connect?C=17458&P=97869,14976,2697&M=COMP&LG=1&I=13&G=G&IDS=169873,170035 JPT-connector] Motronic box, many cars (Audi, BMW, Porsche, Opel, GM) shipped at least from 1985..1996. The '''Alubos frontplate for VEMS ECU with the Motronic-55 pin connector''': http://www.vems.hu/files/connectors/AMP/JPT/Motronic/VEMS_motronic55_ECU_21_m.jpg AUDI, BMW, Porsche and Peugeot lovers rejoice. * VEMS Motronic-55 ECU [http://www.vems.hu/gallery/main.php?g2_itemId=63 in an Audi S4], plugs into the place of motronic, driving an AAN engine (same as ADU/ABY). See VemsMotronic55/AudiAan * Audi 3B (engine with different pinout than AAN, only 1 ignition output signal in the factory harness) was also tested. ** actually, most 3B owners want some extra wires so they are able to use 5 ignition coils. * PlugAndPlayMotronic/BmwEngines Does anyone have motronic55 pinout for M20B25 engine (from BMW 325 IX E30 1987..90) ? We received pinout from a guy who made Econoseal-motronic55 adapter harness earlier, but it would be good to verify * PlugAndPlayMotronic/PeugeoutEngines Does anyone have motronic55 pinout for some Peugeout engine (where motronic-55 was used) ? We hope to receive pinout from a guy who made Econoseal-motronic55 adapter harness earlier, but it would be good to verify * PlugAndPlayMotronic/PorscheEngines ... if someone wants it... These can be purchased in [http://shop.vems.hu/catalog/index.php?cPath=1 webshop] [http://www.vems.hu/files/connectors/AMP/JPT/Motronic/VEMS_motronic_frontplate_l.jpg bigger picture] (this bigger picture taken without the pressure nipple) There are many [http://hem.bredband.net/rocco-82/Motronic.xls motronic types], Even with the 55 pin connector. Oops ... broken link. anyone has a backup, or list from other source ?. It makes sense to make hi-tech substitute for * ECM used in many vehicles * vehicles that are often tuned or played with * not too advanced from the factory. It's unlikely that one would swap a new 96-pin motronic. The 1.1 .. 1.3 Motronics on BMW seem to fall in this category. The '''Audi 5cyl engine''' (InputTrigger/AudiTrigger eg. MembersPage/MarcellGal/PowerAndTraction) is a '''primary target''', with either 1 or 5 ignition coils. Other motronic ECU-s, such as Porsche or BMW had similar pinout, but verification and customization is needed. '''Document the desired pin-mapping and genboard options if you want a box with this connector''' customized to your taste. TODO: * collect links * variaties * geometry * pinout(s) * special issues (MAP, MAF signal, trigger?) * extra connection for advanced features (like WBO2) I MembersPage/JohanErikssonluleasweden runs my opel calibra with genboard v3.2 in motronic m2.8(55pin) box. I have placed 3 extra connectors on the top of the box for egt, wb02, boostcontrol. .... ---- Suggestion: Make a daughterboard to mesh with the GenBoard inside the case so that the pinouts can be easily changed either with a jumper board or a custom wiring board, makes it so you can plug it right into a system. Only the little ConnectorBoard would require new layout (easy) for the right connector and the endplate would need done for each type of connector JPT-55p etc.. Digifant I is a definate that could be replaced. It is a common swap into turbo 8v's (VW's) as it has a standard vw wiring loom and is programmable these typically run ~200-300 used. Not including the custom chip, but comes w/ a wiring harness. CIS-* cars: (all have restictive Fuel-air plate) * CIS cars have only JPT7 for the ignition module no other connectors. * CIS-Lambda cars have a O2 jetronic (K-Jet) 25 pin JPT connector But only have idle and WOT switches on the t-body, but there are 4 wires that can be used, good for a bolt on plug in TPS. * CIS-Lambda with knock ( a common conversion for CIS-Lambda cars) [http://www.driversfound.com/scirocco/techtips/engine/knocksensor/ Knock Conversion ] has the JPT-25pin connector for the 02 box, and an additional JPT(I think its a 15pin connector) for the knock box. * CIS-Motronic.. Now there is a beast I know nothing about. fill me in. Biggest market for VW's is problably the current A3 2.0 xflow motors, these motors are readily available, easily turbo'ed, and very good for being modified. Has a VR crank trigger, some have Hall cam triggers (4 window), it is already some type of motronic. and coilpack activated. Higher profitablilty would be the 1.8T 20v motor. has all the right fittings, and sensors. Note: VW needs waterproof design. Mk2, Mk3, Mk4 ECU was placed under windscreen near wiper mechanics. ///GintsK/// ---- '''See also''' PlugAndPlayEEC ---------- Good idea, but I think more usefully way the ecu interchange cabel between the factory ECU connector and the VEMS conector. On this way no VEMS built in MAP sensor. The MAP sensor location in somewhere in the engine compartment and need one more interchange cabel between the VEMS MAP assy and factory MAF connector. Vantages: *Very easy and quick installation. *Factory loom is the best. *No grounding "mistake". *Easy uninstallation. *MAP/MAF change means more torque and HP on higher rpm. *Do not need new design for VEMS. etc... Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.