_______ 
(  ____ \
| (    \/
| (__    
|  __)   
| (      
| (____/\
(_______/
         

______ 
| ___ \
| |_/ /
|  __/ 
| |    
\_|    
       
       

 __     __
 \ \   / /
  \ \_/ / 
   \   /  
    | |   
    |_|   
          
          

         
 ##      
 ##      
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
         

         
 ### ### 
  ### ## 
  ##     
  ##     
  ##     
 ####    
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Ford Sierra Cosworth 2wd Originally with Weber-Marelli engine management. System component:: Sensors: Engine RPM/TDC Sensor The crankshaft pulley has 4 identical teeth spaced at precisely 90°. The sensor sends a signal to the module whenever a tooth passes a the sensor. From this signal the module determines engine speed (RPM) and the TDC position of each piston (crankshaft position). The distributor The distributor is driven by the auxiliary shaft as on the standar ohc engine. A phase sensor, locatoed opposite a cam having two teeth separated at 90° to each other, is fitted inside the distributor. At the passing of a tooth the sensor delivers a signal to the ECU. This signal is similar to the signal supplied by an RPM/TDC sensor fitted at the crankshaft pulley. Both te signal from the distributor and the RPM/TDC sensor enable module to idetify the phase of each cylinder. The Throttle Position Sensor (TPS) This unit is fitted to the throttle shaft and senses the throttle position. at idle speed voltage is 5.0-4.5 volts and at full throttle the voltage drops to 0.5 volt. The Manifold Absolute Pressure (MAP) Sensor Depending on the manifold pressure, the sensor regulates between 0.25 to 4.75 volts. If manifold pressure exceeds 0.9 bar, the sensor signals the ECU to cut-off fuel. The Air Charge Temperature (ACT) Sensor This sensor is of the NTC resistor type, its resistance decreases as temperatures increase. Engine Coolant Temperature (ECT) Sensor The ECT is also of NTC resistor type and its operating range is identical to that of the ACT. Actuators: Ignition module The ECU sends a Spark-out signal to the ignition module to trigger an H.T. pulse by switching the coil primary circuit off. The Fuel Injectors The ECU provides accurate control of the solenoid operated fuel injectors to discharge fuel. The Idle Speed Control (ISC) Valve This unit is regulates the engine demand for air depending on the engine temperature, engine load, or swithed on accessories. The valve, whichis controlled by a variable current from the ECU, adjust the air flow into the engine. The valve is pwm modulated. The Boost Pressure Control Valve This solenoid valve is directly connected to the high pressure side of the turbocharger by a hose. Depending upon whether the valve is open or closed it will either "vent-off" a portion of the boost to the inlet side of the compressor (valve open) or direct it to the wastegate actuator (valve closed) I need some advice about the hw configuration of vems. -Can I use this VR sensors? -This Vr sensor configuration is suit for VEMS? -What type of ignition driver configuration do I need? -
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.