##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
         

 _       _ 
( )  _  ( )
| | ( ) | |
| | | | | |
| (_/ \_) |
`\___x___/'
           
           

 _     
( )    
| |    
| |  _ 
| |_( )
(____/'
       
       

         
     ##  
     ##  
  #####  
 ##  ##  
 ##  ##  
  #####  
         

         
 ##      
 ##      
 ## ##   
 ####    
 ## ##   
 ##  ##  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Ford Sierra Cosworth 2wd * '''4 cylinder inline engine, with fire order 1,3,4,2''' * displacement: 2L Originally with Weber-Marelli engine management. ---- '''Trigger''' Engine RPM/TDC Sensor - '''VR type''' The '''crankshaft pulley has 4 identical teeth spaced at precisely 90°'''. The sensor sends a signal to the module whenever a tooth passes a the sensor. From this signal the module determines engine speed (RPM) and the TDC position of each piston (crankshaft position). http://www.cosworth.hu/content/vegyes/vems/crank_sensor.jpg Note that pistons are 180 crankdegrees apart, so half of the pulses do NOT belong to pistons. This means this sensor requires camsync to operate. Not as convenient as a normal Bosch 60-2 or Rover K4-type pattern. The distributor phase sensor (camsync) - '''also VR''' The distributor is driven by the auxiliary shaft as on the standard ohc engine. A phase sensor, located opposite a cam having '''two teeth separated at 90°''' (camdegrees) to each other, is fitted inside the distributor. At the passing of a tooth the sensor delivers a signal to the ECU. This signal is similar to the signal supplied by an RPM/TDC sensor fitted at the crankshaft pulley. http://www.cosworth.hu/content/vegyes/vems/distr_phase_s.jpg The signal from the distributor and the RPM/TDC sensor together enable module to identify the phase of each cylinder. Note: the polarity of both sensors must be investigated. This is simple, but shouldn't be forgotten. And inverted if necessary, considering that the VR input HW senses the 0-crossing falling edge. (internally rising edge is configured when VR is used, since that is the output of the VR chip; but the VR input is always falling edge). Unfortunately '''this trigger arrangement is not currently supported by firmware.''' * with only 1 campulse, it is supported. Short-dwell ignition transformer (or CDI) is required for high RPM * Is the crank-pulley special in some way ? Is there a chance it can be swapped for a ** multitooth pulley? (available in junkyard, as a long-lasting part that lives well beyond the engine) - under investigation... ** 2 pulses, 50..90 crankdegrees TDC would also work (grindoff ?) with 1-pulse camsync, but a multitooth is unbeatable. *** Original setup must workable with ECU swap, so grindoff not possible. * how many engines are planned of this install ? It is possible to add firmware support, but it's not without costs ** I plan to build 3 engine with vems at first, but this engine management system is used by most of cosworth (Sierra Cosworth 3 door, Sierra Cosworth 2wd saloon, Sierra Cosworth 4wd saloon, and big-turbo Escort Cosworth) - cost approx.??? (It will be the finest sollution ---- '''Other sensors''' - seems very smooth The Throttle Position Sensor (TPS) This unit is fitted to the throttle shaft and senses the throttle position. at idle speed voltage is 5.0-4.5 volts and at full throttle the voltage drops to 0.5 volt. The Manifold Absolute Pressure (MAP) Sensor Depending on the manifold pressure, the sensor regulates between 0.25 to 4.75 volts. * If manifold pressure exceeds 0.9 bar, the sensor signals the ECU to cut-off fuel ** the threshold is just configured in the ECU, no plus wire. The Air Charge Temperature (ACT, MAT) Sensor This sensor is of the NTC resistor type, its resistance decreases as temperatures increase. Engine Coolant Temperature (ECT, CLT) Sensor The ECT is also of NTC resistor type and its operating range is identical to that of the ACT. ---- '''Actuators:''' Ignition module The ECU sends a Spark-out signal to the ignition module * by factory it's a simple distributor+coil setup, not wasted spark ** is it allowed to use wasted spark or COP / CNP ? The trigger does allow, but do the racing regulations also allow ? *** Engine is not homologed now. But in hungarian rallyecross this engine is running with wasted-spark configuration nowadays. * sounds like ECU needs to be ordered power (IGBT) output and dwell is controlled by ECU * dwell is totally governed by the module and cannot be adjusted, unfortunatelly no more data about ignition module * module input signal is ** logiclevel ?? ** or power signal (pulled to GND) ? '''Coil''' - would you really want to use the unknown ignition module when this coil could be driven directly ? * Bosch, high output breakerless ignition type * output 25.0 kV (min) - open circuit condition * primary resistance 0.7-0.9 ohm * secondary resistance 4500-7000 ohm The Fuel Injectors The ECU provides accurate control of the solenoid operated fuel injectors to discharge fuel. The '''Idle Speed Control (ISC) Valve''' This unit is regulates the engine demand for air depending on the engine temperature, engine load, or swithed on accessories. The valve, whichis controlled by a variable current from the ECU, adjust the air flow into the engine. The '''valve is pwm modulated'''. The Boost Pressure Control Valve This solenoid valve is directly connected to the high pressure side of the turbocharger by a hose. Depending upon whether the valve is open or closed it will either "vent-off" a portion of the boost to the inlet side of the compressor (valve open) or direct it to the wastegate actuator (valve closed) I need some advice about the hw configuration of vems. * Can I use this VR sensors? ** yes * Is this Vr sensor configuration suitable for VEMS? ** not in this form without firmware modifications * What type of ignition driver configuration do I need? ** sounsd like IGBT, but more info on the "ignition module" is needed to tell for sure. Since only 4 cyl, 4+4 can be a good bet to suit either. * Do I need power flyback? ** recommended. Thx any help!
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.