_    _ 
| |  | |
| |  | |
| |/\| |
\  /\  /
 \/  \/ 
        
        

         
         
 #     # 
 #  #  # 
 #  #  # 
 #  #  # 
  ## ##  
         

 _       
( \      
| (      
| |      
| |      
| |      
| (____/\
(_______/
         

     ##  
     ##  
  #####  
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
         

    #    
         
   ##    
    #    
    #    
    #    
   ###   
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
The car got an '''1.6L 4cyl NA engine''' because it is believed to better compete in that class, compared to the 1.8L engine. The '''deadlines are very tight''', it should be ready for race before 2006-03-17 With a standard trigger, it should be no big deal, but this engine has a '''special trigger'''. ---- '''IAC''' Simple bipolar stepper - should be straightforward ---- '''Ignition''' '''Wasted spark.''' Coil on plug style. Yes, only 2 transformers, each have a second high voltage connection for the cyl pair (1-4 and 2-3). ---- '''MAP / AlphaN''' The engine has a MAP sensor. However, because of very aggressive cams, some loadsites might need to be tuned from TPS (AlphaN). ---- '''Trigger''' - Rover K-series wheel (we refer to it as "elise" trigger) The engine has camsync, but because of wasted spark, only primary trigger will be used for now. * '''Primary trigger VR''' This crankwheel is very smart construction, because it can sync in half revolution (often even earlier!). * Early startup is supported (the right output channel will be fired as soon as it can be found). * camsync is currently not fully supported for this elise trigger (recommended to keep secondary_trigger disabled in config) We made some modifications to signalgen to generate the wav sound files to test the trigger setup on the table. Firmware code was tested against this. http://www.vems.hu/files/MembersPage/YasecElise/Lotus_crank_wheel_36-hell_counted_s.jpg The trigger is supported from 1.0.38 with the following setting (multitooth, no camsync) MAKE SURE YOU TRY THESE TOO, there is a mismatch right at the very first (primary_trigger=00 is not 01 although it might work with both edges if the sensor is HALL for sure): * primary_trigger=01 # multitooth (advanced filter is not applied; actually, advanced filter could work with N-1 setting) * secondary_trigger=02 # disabled * another_trigger_tooth=12 # decimal 18, no surprise * tooth_wheel=20 # decimal 32, no surprise (36-4 wheel) * trigger_tooth=04 # 0..12 could work with different TDC position; 4 seems right with above drawing * ign_tdcdelay=78 # decimal 120, that is 60 degrees; according to drawing, TDC is 60 degrees after tooth 4 ** this can be varied of course, but F0 sounds way too high (adjust trigger_tooth instead); ** is it possible to check with timing light ? * ignchmax=03 # fire ign channels 3..0, and ign sequence: * h[2]=02 03 02 03 00 00 00 00 ** assuming 03 channel (EC36pin36) is wired to fire spark for cyl1 and 4 ** 02 channel (EC36pin34) fires cyl2 and 3 Take InputTrigger/TriggerLog to check the tooth pulsetrain correctness. (upload the binary too, and possibly the output after formatted with ''perl binary.pl < terminal.log > terminal.txt'' ) ---- A describtion of the trigger (HU; just to confirm the direction and position seen on the image): <code> Mind1, itt küldöm a képet, immáron dedikált lendkerékkel. A felsõ holtpont fizikailag ott van, ahol a lendkerék tövében a csap van. (azaz van 6db felfogató csavar + 1 tájoló csap, na a csap van felül holtponton) A jeladó ehez képest lejjebb van, gondoltam azt a bordát jelölöm meg, amit "lát" a szenzor felsõ holtpontban. Komikus mód ez úgy semmilyen rendszerben nincs semmivel se. Utána a forgásirány szerint még kettõ bordát "olvas" a szenzor, és kezdõdik az elsõ kihagyás. Udv Yas Azt hittem soha nem fox feliratkozni.:) Lenne 1 kersem:) Ha lehetne akkor kommentalnad magyarul is a torteneseket? Lassan azert tanulok angolul:) A_Feri/Saybor:) </code> --------------- Here are the configuration files: [http://www.vems.hu/files/MembersPage/YasecElise/config.txt config] [http://www.vems.hu/files/MembersPage/YasecElise/tables.txt tables] [http://www.vems.hu/files/MembersPage/YasecElise/trig1.txt triggerlog]
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.