#####  
 ##      
  ####   
   ####  
 #    #  
 #####   
         

 ___   
(  _`\ 
| ( (_)
| |___ 
| (_, )
(____/'
       
       

         
         
  #####  
 ##  ##  
 ##  ##  
  #####  
     ##  
 #####   

         
         
  #####  
 ##  ##  
 ##  ##  
  #####  
     ##  
     ##  

         
         
  #####  
 ##  ##  
 ##  ##  
  #####  
     ##  
     ##  

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Volvo S70 T5 Turbo Motronic 4.4 Ecu 19T 21psi cca 340Le Engine: B5244T LPT 9:0:1 2445 ccm 5 cyl Na camst Rs500 intercooler S60R Fuel injectors 42lb Walbro 255 Lph pump TD04HL-19T Turbo 3" exhaust Msd ignition(distributor) ----------------------------------------------------------------- New Project: 1998 Volvo S70 B5244T + vems V3 Engine: B5244T LPT 9:0:1 2445 ccm 5 cyl Na camst Rs500 intercooler S60R Fuel injectors 42lb Walbro 255 Lph pump TD04HL-19T Turbo 3" exhaust Volvo T5 COP's Bosch 0221604001 ----------------------------------------------------------------- Inline 5-cylinder, sequential ignition with camsync Primary trigger: 60-2 w/ VR sensor. Secondary trigger: Single tooth w/ Hall sensor. The rising edge of the cam wheel hits the sensor after cylinder three fires and before cylinder one does. Firing order is 1-2-4-5-3. Ign. outputs will connect as follows (for 2+6 igbt configuration, + PNP transistor Ignition outputs * cyl 1, EC36/34 * cyl 2, EC36/35 * cyl 4, EC36/33 * cyl 5, EC36/36 * cyl 3, EC36/24 ----------------------------------------------------------------- Sensor: TPS is standard Volvo S70 , 3 pin. -Standart Vr sensor 2 pin -Hall sensor 3 pin -Bmw Mat sensor -2 Bosch Lamda -IAC 3-pin ----------------------------------------------------------------- Coil pin-out:S70 T5 Cop Pin---Designation 1 Trigger 2 Not Used 3 Ground 4 +12v ----------------------------------------------------------------- '''ign TDC-delay (primary trigger settings) is too low !''' * ign-tdcdelay = 20 is wrong.... Correction hint: 144+20=164 crankdeg = 15*6 + 74 * first trigger tooth should be 15 * "TDC after the trigger": ign tdcdelay = 74 crankdeg * of course, rotate ignoutputs by 1 to match the desired spark position ** verify by strobe ---- '''Validation shows possible problem''' * sectrig HALL-dirac filter: preferrably disable it ! * iac ignadv change should be lower (+2, -6 crankdeg or similar; even +1 -3 or crankdeg is more than enough is IAC air-valve is set up properly, +0 -0 should be good too) With hall dirac filter the problem shows less times ---- '''Benchtest''' We applied some changes to the config, because "TDC after trigger" = 20 crankdeg is not a good setting (see above ... Since we changed 144 crankdegrees, you might need to rotate the ignoutput sequence by 1 event, strobing will show it). After that, we benchtested the config. We '''benchtested the ~160 kPa and 3000 .. 7000 RPM range most extensively where your cylinder seems to misfire'''. The ignition and injection outputs fired properly. Test config: http://www.vems.hu/files/VolvoS/tested-v3.3_u004521-A-2013.05.06-12. ----------------------------------------------------------------- http://data.hu/get/6564404/v3.3_u003132-2013.05.21-00.44.37.vemslog
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.