#     
   #     
 #####   
   #     
   #     
   #  #  
    ##   
         

         
         
 ##  ##  
 ##  ##  
 ##  ##  
  ####   
   ##    
         

    #    
 ######  
   ##    
   ##    
   ##    
   ## #  
    ##   
         

         
         
  ####   
 ##  ##  
 ##  ##  
 ##  ##  
  ####   
         

         
  ###    
   ##    
   ##    
   ##    
   ##    
  ####   
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassa Start]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassa%2FQuestions Questions ]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaInjector Injector] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaIgnition Ignition] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FTrigger Triger] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FDisplay Display] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaWbo Wbo] ||[http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaConfig Config] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaTable Table] ||[http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassawiring Wiring]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaIdle Idle] || '''Trigger''' * Used a 36-1 trigger wheel on the crankwheel, as i´m thinking of using the OE parts ** or if it´s get to tricky, i will just get the complete Edis system, Edis , was what i run on the 300hp 4AGZE,and it was working great, I have just ordered a 20feet container in Japan with engines,so it will be about 2month, before they get here, Why we removed 2 teeth 180 degrees apart on the 24 trigger become PhatBob recommended this set-up. The trigger and vr is located at the camshaft i.e. distributor driven. * VehicleFitment/Toyota/Triggers Primary trigger Edge = Rising Type= Multitooth Filtering= Disabled Advanced Filtering= Disabled Special N-1= Disabled Fiat Stilo= Disabled TDC after the trigger=127.5 Number of teeth on the wheel=11 Trigger tooth=1 Next trigger tooth=6 Crank min. period= 3000 Tooth width= Angular width of tooth=30 Tooth Relation normal=121 Tooth Relation Missing=181 Phase Angular width of missing tooth=60 Engine phase when to reset=216 THE CAR STARTED with another Vems ecu,and i found out that the ecu is not working right! * if it's not responding on the VR input signal, the only reason for this (since it's never sent without input-trigger test) is that bad GND and GND5 connection broke the TPIC6A259 (p259) chip and that pulls down the LM1815 (VR-trigger sensing chip) supply disabling it's operation. Make sure that GND and at least 3 (preferrably 4, with EC36pin22) GND5 are always connected preferrably very close to EC36 (max 40cm), and don't have the chance to come apart during operation. Check [http://shop.vems.hu/catalog/index.php?cPath=1 your configuration's pinout in webshop] Verify p259 outputs (eg with mdh commands) GenBoard/Manual/DigitalOut/Table, if the p259 chip was damaged it needs to be removed or replaced. Will check more tommorrow!. '''make sure to publish your used config in Manmcdmct dump format''' to make it easy to reprocude (and eliminate any problem with using unsuitable MegaTune for given firmware, or vemsv3.ini error)
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.