#### ### 
 ##   #  
  ####   
  ###    
 #  ##   
###  ### 
         

         
         
  ### #  
 #   ##  
 #   ##  
  ### #  
      #  
  ####   

  ____  
 |  _ \ 
 | |_) |
 |  _ < 
 | |_) |
 |____/ 
        
        

   ___  
  / _ \ 
 | | | |
 | |_| |
  \__\_\
        

 _______ 
(  ____ \
| (    \/
| (_____ 
(_____  )
      ) |
/\____) |
\_______)
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Target Car: Bmw 325 (currently Motronic 1.3) 2.5L 6cyl I6 engine Aims * Sequential sparking * 300 dergee camshaft ---- '''Problem - solved''' by uploading a good config * In MegaTune everyting works expect the Spark angle. ** do you have an LCD ? does it show roughly the same ? *** We have LCD. Yes we see the same. Spark angle show -01. *** We put firmware v0.36 nad later 0.58. but still the same problem. The Megatune is 2,25 version. (everytime we run Megatune in the begining show "this wrong version.... Can we terminate the program?" ** the spark angle changes just now, getting a 64 degree offset (so display range changes to -64..+64 degree) this is a one-liner in vemsv3.ini but indeed an incompatibility between most recent and older MegaTune / firmware (direction: new MegaTune shows -55 degrees with an old firmware, when the real ignadv is 9 degrees) See IssueReports on what information is needed to be able to help. * MegaTune version * firmware version * config and tables ** mcd dump *** most importantly: ign_balance ** mct We filled the Spark table but th Spark angle indicator show -1,75 degree instead of ... degrees at RPM= and MAP= ... WE SOLVED the problem with upload a good config and table. ---- '''Air and Coolant Temp Characteristics''' Now the following question. How I can make a Air tempereture characteristic. * I used EasyTherm program to make a *.inc file ** we use hexpatch (found on EasyTherm page) to upload a previously generated tables (gets very close; start with 2252_256, since the most common sensors are appr around that) * How can I convert *.inc file to *.hex file? ** this is in fact a good idea. propertherm.pl has the code, but we should release a small win (and linux) program (written in C) that does this (either from .inc or from the 2 main parameters "2252,256") : this way the gourmans can tune without much wizardry ----- * We have 6 injectors in the bmw. 3 injector connected in paralell. Can I do the same in Vems output, I mean Is it possible to swith 3 injetors with one output (igbt)? ----- Succesfully day for the national. We crank our engine and its starts for first time. It was great pleasure for us. We are really happy! And I have a Birthday today! :) ----- PROBLEMS: 1. The Ego Correction does not work. It switching On and OFF 1 second periodically. - The lean Limit: 15% - Rich limit: 2% - Step 1% - Speed change: 50 we tried to cahange the parameters but it is doing the same. What could be the problem? 2. we have dual solenoid motor for Idle. How can I set up the output for the Idle control? I would like to use - EC36-pin6 to IAC close pin - EC36-pin17 to IAC open pin Thank you for help
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.