## ### ## ## ####
___ ___ | \/ | | . . | | |\/| | | | | | \_| |_/
###### # ## # ######
______ | ___| | |_ | _| | | \_|
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: UPDATE 2017-09-14 This is still an issue. The noise from the starter motors on these engines is bad for standard VEMS ECU VR trigger input. To get the customer out the door I have had to install other ECU brand (I have seen Nira i3, MaxxECU, Link work out of the box) and had no issue. Unfortunately the Volvo T5 and T6 engines are popular among swedish customers. What kind of simple/easy filter could be added to the VR trigger input to get it more immune to the noise? ---- UPDATE: 2015-09-17 I have run into this problem again! This time with a Volvo 740 1990. And first gen volvo 5 cyl turbo engine. Standard installation with Twinshield. During cranking the trigger is so bad that it does not even fire ignition. See trig logs. Coils and inj unplugged We have tried the following: *Added ground: No change *Polarity switch : no change *Changed sensor: No change. *Changed to Volvo B230 sensor with custom bracket. 0.5-3mm tested, marginally better trigger. *Moved supply and ground for ECU to and from battery, to and from engine block: Minor or no change in trigger. *Changed starter motor : Much better trigger! To the point that the ECU starts so sync sporadically and fires ignition. Then we noticed that during cranking the trigger is rubbish, but when you let go of the cranking, the 2-3 last revolutions of the engine the signal clears right up and becomes perfect! So with patients the car does now start, but its pure luck to its syncs up and start. Maybe 1 out of 20 times. The funny ting is that when its started it runs perfect! No trig error. But the log still look weird on idle. And also, the problem seems to get worse when the starter motor and/or cables get warm. Low battery and cold starter seems to make it better. (Then it starts more frequently) Stock Volvo 740 battery location and cables. http://www.vems.hu/files/ThorbjornEngdahl/Volvo%20T5%20trigger%20problem/No%20plugs.png http://www.vems.hu/files/ThorbjornEngdahl/Volvo%20T5%20trigger%20problem/No%20plugs%202.png On this above, startermotor on and off short intervals, w/o plugs. All files located here: http://www.vems.hu/filethingie.php?subdir=ThorbjornEngdahl/Volvo%20T5%20trigger%20problem Now my questions: What causes this? How is the starter-motor picked up in the trigger? What can be done to prevent this? I tried to pull down the signal with large resistor, no change in signal. Can some kind of filter be used, like the ones for radio interference? We are all out of ideas. But one thing is clear, this problem is common, i have encountered it 4 times now, and here is no solution part from changing to GT101 HALL sensor, that solves the problem. But i would like to get this fixed once and for all. Suggestion from Mattias : * Get a cheap Rigol digital scope. * Try to add +5V pull-up to signal. Not pull-down to ground. ** It looks like the zero-crossing of the signal happens more often than it should. I've had this problem on some Volvo 6 cyl 60-2 trigger wheels where an extra trigger event occurs at the missing teeth at cranking speed, causing a trigger error on every revolution of the engine and no-start. ** The voltage increases just above zero and then drops a few tenths of a Volt below zero, and then goes back up again causing another zero-crossing = trigger event. Raising the voltage with a pull-up resistor lifts this voltage oscillation above ground, causing no zero crossing and no more ghost trigger events. ---- ---- '''OLD Post, may or may not be relevant''' Volvo 245 with new generation twin VVT volvo T5 engine. VEMS V3.7, twinshield, simens 875cc, volvo 601 coils. We have experienced extreme trigger problems during cranking. Change every singel part inc; V3, Shielded wire VR sensors, 2 different types. Flywheel, 2 different types, one solid billet one and one OEM from -97 850 turbo. What ever we do, there is till always trigger error. Both less primary, and to many primary. Wont even fire IGN coils. We even changed startermotor, and that made the triggerlog much better, but not good enough to start. Tried everyting, dissconnected everyting but VR trigger, still no good trigger. Moved ground to engine. Moved 12v+ supply. Moved the battery from the trunk back to its original place. Tried all kinds of settings and polaritys. Nothing works! http://www.vems.hu/files/ThorbjornEngdahl/T5%20trigger%20problem/1.png Standard trigger wheel brand new sensor http://www.vems.hu/files/ThorbjornEngdahl/T5%20trigger%20problem/7.png The very best we got. Still not good. We got this with very low battery, and changed startermotor. Never seen such a wierd trigger http://www.vems.hu/files/ThorbjornEngdahl/T5%20trigger%20problem/med%2013.4%20vlt.png With jumpercables to antother running car, 13.4 volts http://www.vems.hu/files/ThorbjornEngdahl/T5%20trigger%20problem/Nytt%20hjul.png Billet wheel, New type trigger sensor. All files located here: http://vems.hu/files/ThorbjornEngdahl/T5%20trigger%20problem/ ---- Hello Thorbjorn, I have reviewed your triggerlogs, the log with the standard flywheel looked best but seemed to have swapper VR polarity, could you redo this triggerwheel (stock flywheel if possible), with swapped trigger wires 8-10 seconds cranking without INJ and IGN fuse ? I'll review this new logs we'll work from there. Best regards, Dave --- Hi Dave, Unfortunately the customer chose to return his unit to me. :( I tried polarity change of both wheels, but I didn't name all the logs. All logs are with only VR connected. No INJ nor IGN connected. Same problem, on all configurations, just varying amount of error. Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.