_____ |_ _| | | | | _| |_ |_____|
## ## #### ## #### ## ##
## ## ## ## ## ## ## ## ######
## ## ##### ## ## ## ## ## ## ## ##
##### ## ## ## ## ##### ## ##
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: '''Suzuki with manual transmission''' - 1.3L unknown engine Specifying ECU (inputs, outputs, mechanically) suzuki_swift_wiring_diagrams_1997.pdf is helpful, but not enough, by far. '''OWNER PLEASE CHIME in ASAP'''. The Suzuki connector is mounted in a custom "frontplate", so wiring can be done immediately when pinout is confirmed by the installer/tuner. '''Factory connector should be used.''' * can be placed in VEMS box (best) ** or factory box (seems more difficult to get right) ** or even adapter small harness (not really justified) '''Output''' * '''Logiclevel ignout .. pin10 ''' (no idea if 5v/12v needed). External ignitor triggered from c21/pin10 ORG FAN output? c21/pin20 BLU ** '''CURRENT rating ??''' Idle valve type ? PWM type, c21/pin24 GRY/RED Tach out? Tach is triggered from coil directly, not from ECM. Other ? '''flying loom EC10 or SSC would be nice''': * a few extra outputs * a few analog inputs (min 2 pulledup, min 1 with no pullup) ---- Ecu requirements: * primary trigger: VR * secondary trigger: VR * MAP: offboard * Ignition outputs: 2 logic level + 6 IGBT ---- '''Pins for FETs (by default 30V flyback, mark where low voltage flyback required) should be defined now''': (exact mapping enough during manufacturing) injFETs . Injout Pins: * EC36/7: INJA Fuel injector throttle body: c21/pin12 YEL/BLK * EC36/19: INJB Tank pressure control valve: c21/19 RED/BLU * EC36/8: INJC EGR Solenoid: vacuum valve 2: c21/pin5 RED/BLK * EC36/20 INJD EVAP Purge: c21/7 RED/GRN * EC36/9 INJE EGR Solenoid vacuum valve: c21/pin6 GRN * EC36/18 INJF EVAP can vent: c21/3 RED/WHT * EC36/6 INJG: IDLE valve: c21/pin24 GRY/RED '''needs low voltage flyback diode''' * EC36/17 INJH: .... FLYBACK * EC36/23: Flyback/IGN PWR, c21/pin15 WHT/BLU IDLE voltage supply: * connect c21/pin2 WHT/BLU to c21/pin11 GRY/YEL (ISC motor control 12v supply) ignIGBT ignition out pins: * EC36/11: IGN 04: External igniter triggered: c21/pin10 ORG ''' logic level''' * EC36/34: IGN 02: Main relay c21/pin22 BLU/BLK * EC36/36: IGN 03: Fuel pump relay c21/pin21 PNK/WHT * EC36/33: IGN 01: ISCA relay c21/pin16 GRY/BLK * EC36/35: IGN 00: EFE Relay (early fuel evap) c21/pin25 YEL/RED * EC36/10: IGN 07: Rad Fan relay c21/pin20 BLU * EC36/24: IGN 06: .... P259 out pins: * EC36/30 P259/7: MIL light c21/18 VIO/RED v3 POWER: * EC36/25 12v supply: c23/20 BLK/WHT v3 GND: * join GND5 EC36/5, 21, 22, 32 with c21/pin13 BLK/BLU, c21/pin26 BLK/RED * join GND EC36/26 with c21/pin1 BLK/GRN, c22/pin9 LT GRN/BLK ---- '''Inputs''' * VR, VR * EC36/27: primtrig VR c22/pin3 WHT/BLK, c22/pin11 WHT/RED; * EC36/13: sectrig VR c22/pin10 WHT, c22/pin2 ORG * EC36/14: CLT: c22/pin7 GRY/WHT * EC36/2: IAT: c22/pin14 GRY * offboard MAP sensor: ** internal signal: MAP signal: c22/pin5 LT GRN/RED * EC36/28: TPS/MAP 5v: c22/pin1 LT GRN * EC36/26: Sensor GND (MAP/TPS/IAT/CLT): c22/pin9 LT GRN/BLK * EC36/1: TPS: c22/pin6 LT GRN/WHT * NO Knock * EC18/8: Wheelspeed: c23/pin11 YEL/GRN (HALL) * '''A/C ? AC-idle up''' in c23/pin19 BLU/RED; AC Cut-out c23/pin17 LT GRN/RED ** protected mcp3208 analog input OK for AC-idle-up ? * +min 2 mcp3208 analog inputs for later extras (some with pullup) ? ------------- Szerintem jónak tûnik a pinout. -Fero Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.