___  ___
|  \/  |
| .  . |
| |\/| |
| |  | |
\_|  |_/
        
        

 _______ 
(  ____ \
| (    \/
| (__    
|  __)   
| (      
| )      
|/       
         

         
         
 ##  ##  
  ####   
   ##    
  ####   
 ##  ##  
         

  _____ 
 |_   _|
   | |  
   | |  
   |_|  
        

    ##   
   #  #  
   #     
 #####   
   #     
   #     
   #     
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
My name is Stein Ove Prestmo (mk1_G on IRC). I work as an Mechanical Engineer doing 2D and 3D drafts for a living. I live west of Oslo, Norway. Contact info: prestms [at] hotmail [.] com ---- '''The Plan''' My plan is to add GenBoard/VerThree (V3.3) to my project car. The car is a '83 [http://vagner.jeje.je/bilder/albums/album111/IMG_4901_web.sized.jpg VW Golf GTI] with an 1.8T 20V engine. The car is at the moment under restauration and the engine is rebuilt. The engine is an '97 Audi A4 (Engine code: AEB). The original K03 turbo is changed for a K04-023 and exhaust manifold from an Audi S3 / TT 225hp. [http://vagner.jeje.je/bilder/view_album.php?set_albumName=album77 Pictures of the car and the rebuild can be found here] ---- '''Set-up''' My setup will incorporate GenBoard/VerThree V3.3 (build nr.609) with :- 4 Individual Coil On Plugs (dummy ignition)[http://vagner.jeje.je/bilder/albums/album113/AEB_Coils.jpg 1] [http://vagner.jeje.je/bilder/albums/album113/AEB_Coils2.jpg 2][http://vagner.jeje.je/bilder/albums/album113/AEB_ignition_schematics.jpg Wiring Sch.] :- OEM 60-2 wheel on the crank. Pictures: [http://vagner.jeje.je/bilder/albums/album113/Crank_60_2_wheel.jpg 1] [http://vagner.jeje.je/bilder/albums/album113/Crank_side.jpg 2] :- Hall sensor on the camshaft (One window). :- VAG AIT sensor [http://vagner.jeje.je/bilder/albums/album113/AIT.jpg 1] :- VAG water temp. (OEM combined sensor for EMS and Instrumet panel. G2/G62 unit) :- VAG throttle body with built-in idle control InTake/ThrottlePlates/VAGElectronicThrottle Idle switch, Idle engine position TPS and main TPS (I hope to control the idle with PWM the signal to the idle engine) :- Two knock sensors wire in parallell as the firmware doesn't support 2 sensors. :- Wideband lambda sensor. :- 4x 440cc/min fuel injectors (Ford SVO / Bosch high ohm) :- EGT (Sensor mounts in the K04-023 turbin housing in front of the turbine wheel) ---- MembersPage/SteinOvePrestmo/WiringPage ---- MembersPage/SteinOvePrestmo/MyNotes ---- MembersPage/SteinOvePrestmo/MyshoppingList ---- MembersPage/SteinOvePrestmo/SensorPage ---- MembersPage/SteinOvePrestmo/ConfigPage ---- MembersPage/SteinOvePrestmo/TablesPage ---- MembersPages/SteinOvePrestmo/OldBoardPage
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.