## ## ##### ## ## ## ## ## ##
##### ## ## ## ## ##
/'\_/`\ | | | (_) | | | | | (_) (_)
_____ |_ _| | | | | | | \_/
####### ## ## ## ## ## ## #######
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: 11th January 07 Hi every one. This VEMS is being constructed to replace the now useless Rover MEMS1.9 ECU on my Group A rally spec Classic Mini. A Little History The engine is a Single Point Injected, standard stroke, 74mm bore transverse Rover 'A' series engine http://www.austin-rover.co.uk/engineaseriesf.htm . Everything was running well enough before fitting the Ex works ( http://www.wpm.co.uk/worksminis/ ) group A cylinder head, which this particular head from the BMH ( http://www.bmh-ltd.com/ )prepaired cars, had seen and completed the Monte Carlo Rally and the Nurburgring. This head pushed the compression ratio further from the original CR that the MEMS ECU had ignition maps for. This problem was evident when I first built the engine when the CR went from the factory 9.4:1 to 10.5:1. Onset of knock was evident on 95 octane unleaded and just about normal on 99 octane. So I knew something had to be done when calculating the CR with this head to be 11.2:1. What i did to try and overcome the problem of knock was to remove he reluctor ring on the flywheel, retard it by X amount of degrees and re install it, thus retarding the ignition advance right across the map http://www.turbominis.co.uk/_photos/members-motors/286/3070.jpg http://www.turbominis.co.uk/_photos/members-motors/286/3072.jpg http://www.turbominis.co.uk/_photos/members-motors/286/3073.jpg This was good in theory, and probibly still good if you dont retard by too many degrees, as I found out! I retarded by five degrees, not realy knowing that the cold crank degrees is set to 5. So, cold starting on a cold, rainy winters day, its a bitch to start to say the least. I retarded by too many degrees. once the engine is running its fine, though suspect that its not performing as it should. This is where VEMS comes in. To bin the MEMS and replace with a programable ECU and still start, run and drive as though it were a factory ECU for minimal cost. Megasquirt had always been considered, but a fellow TurboMinis ( http://www.turbominis.co.uk/forums/index.php ) member posted about VEMS. I was curious, and, well, here I am. Hoping this is going to be a very exciting project unvaling that lost power of my engine. Baisic spec of the Engine Management System Unipolar Stepper Motor ( more to come on this, I have been researching for some time using Unipolar motors as Bipolar) Throttle body single point injector, Low Z Knock detection (mainly for the future turbo engine, experimental at this stage) Wideband Lambda EGT (mainly for the future turbo engine, experimental at this stage) Original coolant temp sensor Original Air temp sensor DIS coil pack from an MPi Classic Mini ( ditching the dizzy and coil) Original crank angle sensor ( reluctor modified to give 36 -1) I am going to butcher and modify a factory engine loom and hybred it with an engine loom from a late Rover 820 Turbo with DIS and mount the ECU inside the car ---- 13th January 07 This is the salvaged Rover MEMS case that i have decided to use. The middle section needs the original heat sink bars removing to give a little more working space. http://freespace.virgin.net/colin.milne/VEMS/DSCF2319.JPG Locating the GenBoard towards the back of the case using 10mm isolating stand offs, thus still allowing for heat sinking of the components and also room for the MAP sensor. The Econoseal plugs will be in the same orientation in the case as they would be on the GenBoard, connecting the two with wire. All bare terminals/ connections will be insulated with resin filled heat shrink. Q. Hoping to put Flyback Diode in this connecting wire - Econoseal Flyback pin to GenBoard. Please confirm this is an acceptable idea? http://freespace.virgin.net/colin.milne/VEMS/DSCF2320.JPG Looking to put the serial connection 'D connector' through the case some where, for easy connection to the computer. This is how the finished ECU should look with the D connector on the bottom or the back. All will eventualy be sealed. http://freespace.virgin.net/colin.milne/VEMS/DSCF2321.JPG Next update will be on the GenBoard itself ---- 14th January 07 Q - Can some one conform this as V3.3 GenBoard Flyback path? http://freespace.virgin.net/colin.milne/VEMS/DSCF2323a.JPG Q - Can some one confirm the correct orientation of Stepper IC? http://freespace.virgin.net/colin.milne/VEMS/DSCF2323b.JPG Q - Can some one confirm this is the 10uF (1210 size, 35V) capacitor, already installed. It is not in the rescue kit 2. http://freespace.virgin.net/colin.milne/VEMS/DSCF2324a.JPG Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.