#####   
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
         

   ###   
  ## ##  
  ##     
 ####    
  ##     
  ##     
 ####    
         

         
         
 #    #  
 #    #  
 #   ##  
  ### #  
      #  
  ####   

  _   _ 
 | | | |
 | |_| |
 |  _  |
 |_| |_|
        

         
  ###    
   ##    
   ##    
   ##    
   ##    
  ####   
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaSubaru Start]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassa%2FQuestionsSubaru Questions ]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaInjectorSubaru Injector] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaIgnitionSubaru Ignition] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaTriggerSubaru Trigger] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaDisplaySubaru Display] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaWboSubaru Wbo] ||[http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaConfigSubaru Config] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaTableSubaru Table] ||[http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassawiringSubaru Wiring]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaIdleSubaru Idle] || ---- D.28/4-2008 We scoped the oe dwell time, and that is 3ms. http://img.photobucket.com/albums/v41/Denmark/NewFile_07.jpg D.15/04-2008,today there is a cranking signal, cranking 200rpm, without trigger error, juhuuu. I had by mistake made a wrong jumper, so the main trigger was set to Hall, instead of VR. ---- D.14/04-2008,this is a pic of the crank and camsensor signal,that we captured today with a scop ,so this look like its supposed to, but with the current trigger setup in the genboard, there is no rpm activity at all. http://img.photobucket.com/albums/v41/Denmark/Subarutriggerpicture.jpg ---- d.13/04-2008, I have today tried the trigger setup, and there is none rpm activity at all on the rpm gauge, so it does not know its cranking.I checked the wiring again, to be sure that it´s +, that is connected to the EC36-pin27. I teied to disabel the cam trigger, to see if that made a diff, but none, The next part must be to get a scoop on the trigger, to check if a signal is comming trough. Other suggestions would be great. link to trigger : http://www.cauzzi.it/coupe/adaptronic/subaru_6_7_timing_chart.gif ---- this is the hard part, This subaru legacy is running the 6/7 trigger setup. as it seems no one have had this running with a VEMS yet, i hope to have some help setting this up, I will, then ofcourse ducument it,so it will be pnp for other users. This is the current setting, copied from Wiki, have not been tested yet, as i have not had the time yet, But would also like comments, before actuel test. Firing order 1-3-2-4 ---- primary_trigger=29 secondary_trigger=59 tooth_wheel=02 trigger_tooth=00 another_trigger_tooth=03 crank_minper=75 tooth_wheel_twidth1=00 tooth_wheel_twidth2=00 cam_sync_r_edge_phase=00 cam_sync_f_edge_phase=00 reset_engphase_after=04 toothrel_normal=01 toothrel_missing=F0
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.