_______ 
(_____  )
     /'/'
   /'/'  
 /'/'___ 
(_______)
         
         

 ___   
(  _`\ 
| | ) |
| | | )
| |_) |
(____/'
       
       

         
         
 ##  ##  
 ##  ##  
 ##  ##  
  ####   
   ##    
         

         
         
  ### #  
 #   ##  
 #   ##  
  ### #  
      #  
      #  

 __     __
 \ \   / /
  \ \ / / 
   \ V /  
    \_/   
          

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaSubaru Start]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassa%2FQuestionsSubaru Questions ]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaInjectorSubaru Injector] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaIgnitionSubaru Ignition] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaTriggerSubaru Trigger] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaDisplaySubaru Display] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaWboSubaru Wbo] ||[http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaConfigSubaru Config] || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaTableSubaru Table] ||[http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassawiringSubaru Wiring]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaIdleSubaru Idle] || ---- D.10/7-2008 Newest config, from a running car. Peter Jensen says car starts perfectly if pulled, but does not start if cranked. * either analog problem ** VR amplitude is too low, or bias voltage too high. '''Maybe secondary_trigger amplitude or bias problem ?''' ** or cranking motor interference with VR signal ** they say it's ruled out, scope shows signal OK after LM1815 (but they forgot to measure RPM from scope) * the min RPM to fire ignition should be around 127 RPM. Normal cranking RPM for this engine is 165-215 RPM. Would be interesting to know what the RPM actually is, when the engine refuses to start. ***the cranking rpm is with is in the range 170-210rpm, and this is also the case when it cant start. We '''tested this config with 1.0.78''', and after we noticed ign_dualout is used (our tester measures ignch1), and corrected, ign was OK from 80 RPM .. 10k RPM (we raised rev_limit and softrpm_rpm ). *I will try and upload 1.0.78 Something weird must be going on with the actual install. VR voltages would be important to know. *how would you like the voltage measured,under trigger [http://www.vems.hu/wiki/index.php?page=MembersPage%2FSkassaTriggerSubaru threre] is cranking voltage from both vr sensors, both are 4v peak-peak ---- '''Config''' primep_temp_scaling=0D cwl=46 cwh=1E cranking_thres=04 awev=32 awev_temp_scaling=1A awec=C0 warmup_clt_range[0]=00 warmup_clt_range[1]=0C warmup_clt_range[2]=1E warmup_clt_range[3]=31 warmup_clt_range[4]=4F warmup_clt_range[5]=65 warmup_clt_range[6]=79 warmup_clt_range[7]=8C warmup_clt_range[8]=A9 warmup_clt_range[9]=C8 warmup_clt[0]=B4 warmup_clt[1]=B4 warmup_clt[2]=B4 warmup_clt[3]=A0 warmup_clt[4]=8C warmup_clt[5]=87 warmup_clt[6]=7D warmup_clt[7]=6E warmup_clt[8]=69 warmup_clt[9]=66 warmup_rpm_scale=BF req_fuel=46 divider=01 alternate=13 injopen=00 battfac=13 kpafac=6E kpaoffs=37 injocfuel=2A injrampup_battfac=FF injpwm=FF injpwmt=FF als_launch_input=CC rpmk[0]=0B rpmk[1]=B8 tpsdot_kpadot_conf=00 tpsdotrate[0]=02 tpsdotrate[1]=05 tpsdotrate[2]=14 tpsdotrate[3]=28 tpsaq[0]=02 tpsaq[1]=07 tpsaq[2]=0A tpsaq[3]=14 als_cut_mintps=FF tpsasync=02 acmult=C8 tpsacold=96 launch_enrich=00 launch_retard=00 overrun_fuelcut=0F overrun_fuelresume=0F rev_limit=49 airden_ignore=5A config11=31 config12=40 config13=06 batt_cal=C6 fastidle=C6 als_max_cut=00 dbaro=0C tps_low=E9 tps_high=32 fan_temp=F3 fan_hyst=04 fan_channel=40 iac_step_seq=C9 iac_conf=78 iac_max_steps=FF iac_tps_thres=05 iac_cold_idle_temp=A2 iac_warm_idle_temp=AB iac_cold_rpm=8C iac_warm_rpm=55 iac_cold_start_pos=CC iac_warm_start_pos=CC iac_afterstart_rpm=1E iac_afterstart_duration=50 iac_speed=00 iac_kp=6E iac_ki=0F iac_kd=05 launch_rpm=14 iac_integral_limit_dec=32 iac_integral_limit_inc=A0 iac_integral_deadband=05 iac_deadband=0A als_cut_maxtps=00 iac_overclose_interval=02 iac_ref_pos[0]=CC iac_ref_pos[1]=CC iac_ref_pos[2]=CC iac_ref_pos[3]=C2 iac_ref_pos[4]=BF iac_ref_pos[5]=BF iac_ref_pos[6]=BF iac_ref_pos[7]=BF iac_ref_pos[8]=BF iac_ref_pos[9]=BF iac_sol_channel=60 iac_ign_slope=14 softrpm_range=32 iac_ign_advance_limit=14 iac_ign_retard_limit=14 iac_ign_threshold=04 ego_conf=06 ego_lag=02 ego_coolant=B4 ego_maxtps=E6 ego_maxmap=96 ego_minrpm=07 ego_maxrpm=50 ego_warmup=3C ego_lean_limit=33 ego_rich_limit=1A ego_pid_kp=28 als_enrich=00 ego_delta=08 ego_target=19 ego_pid_window=FF wbo2_warmup_ramp=A0 als_react_tps=00 wbo2_abs_limit=E4 wbo2_limit_maxt=A0 wbo2_fallback=B0 wbo2_retry_t=06 wbo2_edgetime_corr=BA wbo2_edgetime_min=50 wbo2_ri_target=96 wbo2_nernstdc_target=89 wbo2_pump_pw_zero=65 wbo2_calibration=BE wbo2_heater_pid_kp=46 wbo2_heater_pid_ki=10 wbo2_heater_pid_kd=1A wbo2_heater_pid_ilimit=80 wbo2_pump_pid_kp=15 wbo2_pump_pid_ki=4E wbo2_pump_pid_kd=00 wbo2_pump_pid_ilimit=84 wbo2_ri_confidence_scale=80 knock_conf=01 knock_sampling_window=F3 knock1_frequency=26 knock1_gain=00 knock1_integrator=0F knock2_frequency=29 knock2_gain=3F knock2_integrator=1F knock_threshold=FF knock_noise_scale=FF knock_max_retard=00 knock_default_retard=00 knock_retard_step=00 knock_retard_delay=00 knock_advance_step=00 knock_advance_delay=00 knock_minrpm=FF knock_maxrpm=FF ve_learn_coolant=D8 ve_learn_max_power=FF ve_learn_rpm_scale=1E ve_learn_kpa_scale=1E ve_learn_ego_scale=43 ve_learn_min_weight=4D ve_learn_speed=FF ve_learn_limit=33 ve_learn_conf=00 lcd_c0=FE lcd_delay=FF lcd_backlight=FF kpa_conf=21 ign_balance=00 als_retard_mintps=FF als_retard_maxtps=00 lcd_default_view=00 primary_trigger=29 secondary_trigger=59 tooth_wheel=02 trigger_tooth=00 another_trigger_tooth=03 crank_minper=BC tooth_wheel_twidth1=00 tooth_wheel_twidth2=00 cam_sync_r_edge_phase=00 cam_sync_f_edge_phase=00 reset_engphase_after=04 ign_tdcdelay=88 ign_dwell14=2F ign_dwell6=38 ign_crank_advance=20 ign_out=72 ignchmax=01 engine_off_delay=04 pump_on_mintime=04 fuelpump_channel=50 inj_stage2_rate=FF inj_stage2_start_tps=FF inj_stage2_start_map=FF als_deact_rpm=FF als_deact_time=01 als_deact_egt=00 als_retard=00 als_rev_limit=40 misc1out_minrpm=00 misc1out_maxrpm=46 misc1out_mintps=00 misc1out_maxtps=B3 misc1out_minmap=00 misc1out_maxmap=82 misc1out_channel=07 misc2out_minrpm=FF misc2out_maxrpm=FF misc2out_mintps=FF misc2out_maxtps=FF misc2out_minmap=FF misc2out_maxmap=FF misc2out_channel=FF act_wot_rpm=FF act_wot_channel=FF act_rpm_rpm=FF act_rpm_channel=FF egt1_cal=47 als_tks_channel=FF boost_conf=ED boost_targetoffs=00 boost_minpressure=41 boost_pid_kp=20 boost_pid_ki=80 boost_pid_kd=01 boost_pid_ilimit=FF boost_channel=4F water_pump_temp=00 hybrid_rpm_a=00 hybrid_rpm_m=00 water_pump_hyst=00 water_pump_channel=76 toothrel_normal=01 toothrel_missing=F0 fuelcut_min_kpa=14 fuelcut_max_kpa=E6 tach_channel=17 tach_div=10 shiftcut_conf=01 shiftcut_channel=FF shiftcut_time=00 softrpm_rpm=4B
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.