#####  
 ##      
  ####   
   ####  
 #    #  
 #####   
         

 _       
( \      
| (      
| |      
| |      
| |      
| (____/\
(_______/
         

         
### ##   
 ### ##  
 ##  ##  
 ##  ##  
 ##  ##  
#### ### 
         

         
         
  ### #  
 #   ##  
 #   ##  
  ### #  
      #  
  ####   

 _____ 
|  _  |
| | | |
| | | |
\ \_/ /
 \___/ 
       
       

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Measured fuel consumption: '''1941 km / 1 liter gasoline'''. '''Controlled by VEMS''' (of course). Next goal is 2000 km / 1 liter gasoline. A low-consumption daily driver runs appr 10-16 km / 1 liter gasoline. But this is a competition car, admittedly not very convenient (and unsuitable for bumpy roads), of course. Among the world's [http://www.eco-marathon.hu/ most fuel efficient vehicles] with internal combustion engine (battery and fuel cell are different technology and 1 MJ to 1 MJ based comparison that journalists often practice makes little sense). http://www.eco-marathon.hu/galeria/verseny2/06_t.jpg * low drag (Cd ~ 0.1 - similar cars often claim 0.08 - it's hard to measure exactly) * appr 20kg (without driver) ** 20kg is '''record weight''' in its class. The next in this class is above 30kg. Subpages: * MembersPage/ShellEcoMarathonHungary/ControlledCarburetor ** note: the [http://mac6.ma.psu.edu/stirling/reports/19970012689_1997021349.pdf professional 60kW DOE Stirling] used air to atomize fuel (section 3.1.1). Could we use something similar ? CR = appr. 16 1 cylinder 4-stroke engine (bore=27mm, stroke=60 mm). ---- '''Lista''' - vinni kell: * még egy COP gyújtótrafó ** 2 csatlakozó a gyújtótrafóhoz * LSU4 WBO2 szenzor (18x1.5mm menet) * WBO2 anyacsavar (18x1.5mm menet) * WBO2 csatlakozó (+ receptacle saruk + kisgumi) * pneumatic connectors * HALL-HALL ECU (MAP szenzor, 115 kPa elég) ---- '''Trigger, pozíció jeladó''' * HALL, 1 pulzus ** 42 (or 45 ?) deg BTDC ** falling or rising edge ? ** We need to '''strobe the engine !!!''' ---- '''Pillangószelep / Throttle''': léptetomotoros vagy PWM-es details: MembersPage/ShellEcoMarathon/Servo '''Coolant(CLT) sensor bekötése''' Elvileg ez egy NTC szenzor lesz 2 kivezetéssel, ill. lehet a föld az a senzor háza Az EC36/26 GND és a EC36/14(CLT sensor) pontok közé kell bekötni (a 14-es láb belül fel van húzva 5V-ra egy 2.7kOhm os ellenállással) Ha megvan akkor a realtime muszereken a coolant mutatja (kesobb kalibralhato tobbfelekeppen, pl. a 17 pontos gorbevel). ---- '''Config''' 2010-07-20 A feltöltött konfigot teszteltem 1.1.80-on, befecskendezés müködik rendesen ---- '''Wiring''' * EC36/17 injection * stepper A-B ignition '''Lambda szabályzás''' Beállítás: Base setup/EGO Closed loop control *Lean limit: ha a lambdatargetnél dúsabb, akkor megpróbálja csökkenteni az injektor pulzusszélességet, max ennyivel *Rich limit: ha a lambdatargetnél szegényebb, akkor megpróbálja növelni az injektor pulzusszélességet, max ennyivel * ha 0 akkor nincs korrekció Az EGO Correction muszert érdemes figyelni. Ha nagyobb 100%-nál akkor éppen hozzáad a pw-hez, ha kisebb 100% akkor elvesz a pw-bol. ---- '''Self Dyno''' Breakpad control can made by PWM IAC control, just connect the high power FET output to the breaking motor and the other side of the motor to 12V. The max PWM duty of the IAC output need to set lower than 50% (this means 6V effective maximum)
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.