_______ 
(  ___  )
| (   ) |
| |   | |
| |   | |
| |   | |
| (___) |
(_______)
         

         
         
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
    ##   
 ####    

  ___  
 / _ \ 
/ /_\ \
|  _  |
| | | |
\_| |_/
       
       

 _     
| |    
| |    
| |    
| |____
\_____/
       
       

 __     __
 \ \   / /
  \ \_/ / 
   \   /  
    | |   
    |_|   
          
          

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
||MembersPage/Sascha/SchnellEthritysix/Afreshissues||MembersPage/Sascha/SchnellEthritysix/ECUissues||MembersPage/Sascha|| === Schnell Engineering E36 M52B28 24V Turbo=== ---- === Basic Info: === * **Current configuration** **Primary Trigger: OEM 60-2 Wheel and Hall sensor **Cam sync: YES **Injectors: 6x Injector Dynamics 1000cc (will run @ 3.5BAR) **Ignition: OEM COP **TPS: E36 TPS **CLT: Stock BMW Coolant sensor **IAT: GMWebshop **IAC: OEM **Knock: 2 ch **Launch Control: Of course :) === Engine === * **Built M52B28** **8.8:1 Compression Weisco Pistons @ 85.5mm **Eagle Rods + ARP bolts **ARP Main studs **Stock M52 crank (balanced) at 84mm stroke **Effective displacement 2.9L **SPA T4 bottom mount **Comp Turbo 6065 BB T4 .68 **3" DP and Exhaust **Stock M50 Intake Manifold **S52 Cams **ARP Headstuds === Ordered V3.6 ECU: === * **1 x Assembled v3.7 controller** ** EGT input: 1 ** Flyback: 30V flyback ** ignition driver: 8 ** Knock input channels: 2 ** LCD connection: no ** MAP connection: off board ** primary_trigger: HALL ** secondary_trigger: HALL ** Other options: Wheel speed input Added LCD header to main board and integrated 2x16 LCD display into E36 Cluster. https://lh5.googleusercontent.com/-HbN_Iy3VIHc/U0Cnca9WDGI/AAAAAAAAUmI/m2CEJ9wUc-4/w800-h600-no/IMG_20140405_210126.jpg Wondering if it is possible to get one or two custom LCD layout pages for 2x16 display made? suggested: EGTxxx Cxxx Axxx LAMx.xx VBATxx.x and EGTxxx Cxxx Axxx AFRxx.x PSIxx.x C = CLT A = IAT What firmware are you actually using currently for 2x16 ? V3 firmware is compiled for 4x20 LCD; does that show up that way on 16 column display ? ---- '''Change COP from dumb to active (VAG COP)''' Modified the ECU on IGN output 0 & 1 to logic level output by removing FET and adding bridge to output pins and 500 ohm resistors: https://lh6.googleusercontent.com/-kREPctPTij8/U0R---eKJ5I/AAAAAAAAUr4/x2iZk2SUxVo/w800-h600-no/IMG_20140408_185658.jpg Using all 4 stepper outputs + IGN output 0 + 1 for sequential IGN. Dwell set to 1.4ms with scale of 10 https://lh5.googleusercontent.com/-9ntms8xOVKo/U0RnAfxyjPI/AAAAAAAAUqg/ymozccXWheQ/w800-h600-no/IMG_20140408_171501.jpg Wire harness is temporary and will be remade: https://lh4.googleusercontent.com/-sfsHCt0A_c8/U0STQ9H7ibI/AAAAAAAAUs8/fO177Inm9R0/w800-h600-no/IMG_20140408_202401.jpg
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.