##  ##  
  ####   
   ##    
  ####   
 ##  ##  
         

         
         
  #####  
 ##  ##  
 ##  ##  
  #####  
     ##  
     ##  

   #     
   #     
 #####   
   #     
   #     
   #  #  
    ##   
         

         
         
  ####   
 ##  ##  
 ##      
 ##  ##  
  ####   
         

 #       
 #       
 # ###   
 ##   #  
 #    #  
 #    #  
 #    #  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
||MembersPage/Sascha/SchnellEthritysix/Afreshissues||MembersPage/Sascha/SchnellEthritysix/ECUissues||MembersPage/Sascha|| === Schnell Engineering E36 M52B28 24V Turbo=== ---- === Basic Info: === * **Current configuration** **Primary Trigger: OEM 60-2 Wheel and Hall sensor **Cam sync: YES **Injectors: 6x Injector Dynamics 1000cc (will run @ 3.5BAR) **Ignition: OEM COP **TPS: E36 TPS **CLT: Stock BMW Coolant sensor **IAT: GMWebshop **IAC: OEM **Knock: 2 ch **Launch Control: Of course :) === Engine === * **Built M52B28** **8.8:1 Compression Weisco Pistons @ 85.5mm **Eagle Rods + ARP bolts **ARP Main studs **Stock M52 crank (balanced) at 84mm stroke **Effective displacement 2.9L **S52 Cams **ARP Headstuds **Stock M50 Intake Manifold === Turbo kit === **Ar design v1 top mount manifold - twin MVS gates **Garrett GT4094R - 0.92 AR - T4 **3" DP and Exhaust **Treadstone TR1235 3.5" IC + SS charge piping **Tial BOV === Ordered V3.6 ECU: === * **1 x Assembled v3.7 controller** ** EGT input: 1 ** Flyback: 30V flyback ** ignition driver: 8 ** Knock input channels: 2 ** LCD connection: no ** MAP connection: off board ** primary_trigger: HALL ** secondary_trigger: HALL ** Other options: Wheel speed input Added LCD header to main board and integrated 2x16 LCD display into E36 Cluster. https://lh5.googleusercontent.com/-HbN_Iy3VIHc/U0Cnca9WDGI/AAAAAAAAUmI/m2CEJ9wUc-4/w800-h600-no/IMG_20140405_210126.jpg Wondering if it is possible to get one or two custom LCD layout pages for 2x16 display made? suggested: ETxxxx Cxxx Axxx LAMx.xx VBATxx.x and ETxxxx Cxxx Axxx AFRxx.x PSIxx.x C = CLT A = IAT What firmware are you actually using currently for 2x16 ? V3 firmware is compiled for 4x20 LCD; does that show up that way on 16 column display ? ** I'm currently running 1.2.23 (previously was running 1.2.10), and yes it currently shows up that way (I was pleasantly surprised to see it display that well) so I'm hoping that it wouldn't take much to change one of the pages like 12+13 to look like my suggestions above. ---- '''Change COP from dumb to active (VAG COP)''' Modified the ECU on IGN output 0 & 1 to logic level output by removing FET and adding bridge to output pins and 500 ohm resistors: https://lh6.googleusercontent.com/-kREPctPTij8/U0R---eKJ5I/AAAAAAAAUr4/x2iZk2SUxVo/w800-h600-no/IMG_20140408_185658.jpg Using all 4 stepper outputs + IGN output 0 + 1 for sequential IGN. Dwell set to 1.4ms with scale of 10 https://lh5.googleusercontent.com/-9ntms8xOVKo/U0RnAfxyjPI/AAAAAAAAUqg/ymozccXWheQ/w800-h600-no/IMG_20140408_171501.jpg Wire harness is temporary and will be remade: https://lh4.googleusercontent.com/-sfsHCt0A_c8/U0STQ9H7ibI/AAAAAAAAUs8/fO177Inm9R0/w800-h600-no/IMG_20140408_202401.jpg ---- Tested and recorded resistance of factory OBD2 CLT sensor for BMW 6 cyl M/S5x motors (North America) - Siemens ECU: https://lh5.googleusercontent.com/-0Qok2tUfKfg/UiOGu7Ui7VI/AAAAAAAAPgw/ZxgJo8X1xWg/s1415/BMW_OBD2_clt_temp_ohms.png
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.