_   _ 
( ) ( )
| | | |
| | | |
| \_/ |
`\___/'
       
       

###      
 ## ###  
 ## #    
 #####   
 ## ##   
 ##  ##  
#### ### 
         

         
         
 ##  ##  
 ####### 
 ####### 
 ## # ## 
 ##   ## 
         

  __  __ 
 |  \/  |
 | |\/| |
 | |  | |
 |_|  |_|
         

         
         
 # ###   
 ##   #  
 #    #  
 #    #  
 #    #  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
This page contains information on helping a a friend with a Audi Coupe with a 5cyl 20V Turbo enigne conversion (like a european Audi S2)... running VEMS, w/ stock Auditrigger setup and stock COP w/o power output stage and 440cc high impeadance Ford Racing injectors. ---- So far, the ECU was ordered setup for Auditrigger, and I assume that one of the grounds was bad and this is why we cooked the P259 chip (confirmed with Jorgen), so it was removed and the two diodes put in place. Before I reconnected the ECU, I reconnected all of the grounds myself (as I didn't install the VEMS in the first place, I just took over when they couldn't figure out the trigger setup). The hall sensor is recieving 5V (from PIN 28 - verified this @ the hall plug - also during cranking), the hall sensor wiring is NOT sheilded! But the original Audi harness is also not using sheilded cable (only for the two VR sensors). I'm also using a 5V pullup with a 22k ohm resistor for the crankhome VR sensor, without this pullup I wasn't able to get any rpm signal to the ECU. The VR sensors are within spec as far as the ohm readings go... One has 974ohm, and the other 1007 ohm. MT does show RPM values when cranking (between 100-180 rpm). ---- I have captured a mmd0c log which can be viewed here: NOTE TO DOWNLOAD THE FILES, CLICK ON THE LINK, SCROLL TO THE BOTTOM OF PAGE AND CLICK DOWNLOAD! http://www.freefileupload.net/file.php?file=files/300806/1156968999/mdd0c.log here the mcd.log: http://www.freefileupload.net/file.php?file=files/300806/1156969552/mcd.log and here the mct.log: http://www.freefileupload.net/file.php?file=files/300806/1156969628/mct.log and also a copy of my MSQ: http://www.freefileupload.net/file.php?file=files/300806/1156969697/20VT+auditrigger+-+base.msq ---- Injector's are connected to the following outputs: Inj 1 - EC36 Pin7 Inj 2 - EC36 Pin19 Inj 3 - EC36 Pin8 Inj 4 - EC36 Pin20 Inj 5 - EC36 Pin9 The Coils are connected as follows: Coil #1 - EC36 Pin35 Coil #2 - EC36 Pin33 Coil #3 - EC36 Pin34 Coil #4 - EC36 Pin36 Coil #5 - EC36 Pin11 Fuel Pump is connected to EC36 Pin10 (IGBT Drive_07) ---- Back to MembersPage/Sascha
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.