##### ## #### ## #####
______ ( __ \ | ( \ ) | | ) | | | | | | | ) | | (__/ ) (______/
|\ /| ( \ / ) \ (_) / ) _ ( / ( ) \ ( / \ ) |/ \|
## ## ## ## ## ## ##### ## ####
## ## ## ## ## ## ###
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: '''BMW M3 1987''' My car is going to be in a report in Bilsport #3 (big swedish carmagazin) ---- '''VeLearning''' New problem. Should tune today and try Velearning. Used values in [http://www.vems.hu/wiki/index.php?page=GenBoard%2FManual%2FConfig%2FVeLearn this] page. But it only change values in the first load bins. And very high values also. Like F1 FA FF and so on. I can se that TPS% moves in display so TPS is working. I seem to be followed by Murphys Law or something. Like this. <code> F1 FA FC FF FB FF FF FF 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 </code> ---- '''WBO2''' <code> wbo2_warmup_ramp=A0 wbo2_warmup_target=FF wbo2_abs_limit=E4 wbo2_limit_maxt=A0 wbo2_fallback=60 wbo2_retry_t=06 wbo2_edgetime_corr=BA wbo2_edgetime_min=50 wbo2_ri_target=96 wbo2_nernstdc_target=8D wbo2_pump_pw_zero=65 wbo2_calibration=C9 wbo2_heater_pid_kp=46 wbo2_heater_pid_ki=10 wbo2_heater_pid_kd=1A wbo2_heater_pid_ilimit=80 wbo2_pump_pid_kp=40 wbo2_pump_pid_ki=2E wbo2_pump_pid_kd=08 wbo2_pump_pid_ilimit=84 wbo2_ri_confidence_scale=80 </code> ---- '''Triggerwheel''' My car is now running fine since i made a new triggerwheel. =) [http://www.vems.hu/files/SamuelLindkvist/triggerwheel/triggerwheel361.jpg This] is the new one. And [http://www.vems.hu/files/SamuelLindkvist/triggerwheel/triggerwheel602.jpg this] the old. ---- '''Alpha-N''' Purchased new cams yesterday. 292/292 with 12mm lift. So now i have to change to Alpha-N. <code> config13=02 //Wideband and Speeddensity config13=06 //Wideband and Alpha-N </code> ---- '''My files''' * [http://www.vems.hu/files/SamuelLindkvist/config.txt config.txt] * [http://www.vems.hu/files/SamuelLindkvist/tables.txt tables.txt] * [http://www.vems.hu/files/SamuelLindkvist/my_make My_make] * [http://www.vems.hu/files/SamuelLindkvist/global.h Global.h] * [http://www.vems.hu/files/SamuelLindkvist/Entries CVS Entries] ---- '''Fuel setup''' 4cyl, 2300cc 236cc injectors (2.4ohm) Bosch 0280150201, 1 in each port massair=2300cc / 4 * 1.2kg/m3 = 0.69g massfuel=massair / 14.7 = 0.047g volumefuel = massfuel / 0.7 = 0.067 cm3 timefuel = volumefuel / (236cc/min) = 17 msec If VE (j[0]) is 200 based, not 100, req_fuel can be 8.5 msec. || cyl || inj || EC36pin # || h[0] # || || 1 || A || 7 || 01 || || 2 || F || 18 || 20 || || 3 || G || 6 || 40 || || 4 || H || 17 || 80 || h[0]=20 80 40 01 00 00 00 00 h[1]=00 00 00 00 00 00 00 00 Pulse starts for h[0]-entries at the relevant trigger pulse (special tooth, eg. the selected trigger_tooth and trigger_tooth+another_trigger_tooth after the first pulse after the missing pulse). ---- '''Ignition setup''' Multi-tooth trigger wheel '''36-1'''. VR-sensor from FORD. 2 ign banks, firering a dual coil with 4 outputs (Wastefire) || cyl || Driver || EC36pin # || h[2] # || mdh || || 1+4 || 00 || 33 || 00 || mdh82 || || 2+3 || 01 || 35 || 01 || mdh92 || h[2]=00 01 00 01 00 01 00 01 ---- Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.