#       
 #       
 #   #   
 #  #    
 # #     
 ## #    
 #   #   
         

         
  #####  
 ##  ##  
 ##      
 ##      
 ##   #  
  ####   
         

         
         
 # ###   
 ##   #  
 ##   #  
 # ###   
 #       
 #       

  ____  
 | __ ) 
 |  _ \ 
 | |_) |
 |____/ 
        

    #    
 ######  
   ##    
   ##    
   ##    
   ## #  
    ##   
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Car is a MK2 1982 VW Scirocco, 1600cc 8-valve K-JET engine with a BLT turbokit installed probably somewhere in the late eighties. Engine has already been prepared for EFI by replacing the K-JET injectors with EFI injectors using custom injector seats and BBM fuel rail. Next step is to get VEMS control the injectors and the ignition coil with distributor ignition. ---- '''TRIGGER OPTIONS''' '''Option 1.''' Stock distributor is fitted with an optical sensor, giving '''one pulse per firing''', approx. 90degress BTDC for each cylinder. Without camsync it needs distributer for ignition of course. This was the first trigger pattern first implemented (around the same time as missing tooth). * batch injection possible, but semi-sequential recommended (fire only 1 at a time, every time the next one, divider=1). * VEMS can control ignition timing with the distributor ignition (coil-type trigger?) ** pretending this signal comes from the crank and configuring it as 2-tooth, none missing ** rather 4 tooth. ** in 1.0.x easy. ** in 1.1.x relatively new firmware needed without camsync (use 1.1.67 or 1.1.69) and set tooth width to 180 degrees, Next trigger tooth=1, reference tooth array = 0, 3, 2, 1, .. .. .. .. vacuum hoses would be removed from the dizzy of course. '''Option 2.''' Mount a '''60-2 trigger wheel on the crank ''' pulley and fabricate hall sensor brackets.. Yes, this option would allow wastedspark DIS ignition. '''Option 3:''' '''4-1 on crank''' (3 pulses, 2 of them are appr 60-90 BTDC; pattern is 90,90,180 crankdegrees). This is the simplest, smallest toothcount pattern that allows DIS. * Possible just 3 M8 screws or similar, that [http://shop.vems.hu/catalog/hall-sensor-p-107.html 1GT101DC] sensor can sense. ** always HALL sensor recommended for low toothcount (not VR). ** make an extremely strong sensor mounting bracket (~as strong that you could lift the engine with). Otherwise vibration will likely cause problems. ---- '''Trigger testing''' Files are [ http://www.vems.hu/files/MembersPage/SVIScirocco/ here] like [http://www.vems.hu/files/MembersPage/SVIScirocco/Testing.txt Testing.txt] and [http://www.vems.hu/files/MembersPage/SVIScirocco/testbench.vemscfg test.vemscfg] We'll reproduce this setup. http://www.vems.hu/files/MembersPage/SVIScirocco/vems_primarytrigger.PNG http://www.vems.hu/files/MembersPage/SVIScirocco/vems_miscoutput.PNG http://www.vems.hu/files/MembersPage/SVIScirocco/vems_ignoutputs.PNG
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.